Channel Plus Telephone Accessories H612 User Manual

ChannelPlus Telephone Entry Module  
SAFETY INFORMATION:  
OpenHousetm modules  
attach from the top  
IMPORTANT INSTRUCTIONS  
When using your telephone equipment, basic precautions should  
always be followed to reduce the risk of fire, electric shock and  
injury to persons, including the following:  
a) Never install telephone wiring  
during a lighting storm.  
1) Hook from the top  
2) Swing into place  
3) Push button to lock  
b) Never install telephone jacks in wet  
locations.  
1. Read and understand all instructions  
1
2. Do not use this product near water, for example, near a bath  
tub, wash bowl, kitchen sink, or laundry tub, in a wet  
basement, or near a swimming pool.  
c) Never touch uninsulated telephone  
wires or terminals unless the  
telephone line has been disconnected  
at the network interface.  
3. Never push objects of any kind into this product through  
cabinet slots as they may touch dangerous voltages.  
Telephone Master Hub (4 lines x 6 phones)  
ChannelPlus model H616  
3
From  
Telco  
Expansion  
Ports  
Telephones  
R
T
RJ31X  
4
3
2
1
R
T
R
T
Out  
R
T
d) Use caution when installing or  
modifying telephone lines.  
4. SAVE THESE INSTRUCTIONS  
2
Wire Color Codes  
The H612 Telephone Entry Module provides a superior method  
of telephone connection to your system. Each unit provides  
surge suppression for two lines and a master disconnect. Also,  
Solid Color  
Twisted-Pair Wire  
RING  
TIP  
brown  
pair 4  
Cat5  
4 pair UTP  
brown/white  
blue  
RING  
TIP  
green  
pair 3  
each line has an LED  
status indicator to warn  
you of a surge event.  
white  
pair 3  
green/white  
Telephone Entry Module (surge,disconnect)  
yellow  
ChannelPlus model H612  
RING  
TIP  
orange  
pair 2  
From NTE  
Line 2  
black  
pair 2  
orange/white  
1
2
3
6
5
4
Telephone  
Output  
red  
Disconnect  
Out  
Surge  
Warning  
Expansion  
Output  
In  
RING  
TIP  
pair 1  
pair 1  
blue  
Line 2  
green  
2
2
3
blue/white  
5
Line 1  
6
5
4
1
2
3
1
2
3
5
Modular connectors  
Line 1  
8 position connectors  
PR2  
PR3 PR1 PR4  
6 position connectors  
PR3  
PR2  
PR1  
PR2  
PR1  
T R T R T R T R  
1
PR1  
R T  
2
3
4
5
6
7
8
Typical Installation  
T R T R  
2
T T R T R R  
5
1
2
3
4
5
6
1
3
4
5
6
1
2
3
4
6
Each line is individually surge protected to 50 Joules and  
RJ-11  
RJ-14  
Dual line telephones &  
answering machines  
RJ-25  
Rare  
3 line KSU  
Install this jumper for normal  
operation. Remove to disconnect  
telephone service from the system.  
4000 Amps. Some surges contain sufficient energy that  
although your system has been protected, the surge  
circuit will be unable to provide additional protection.  
When this happens, the red light for that line will turn on  
and the module needs to be returned for service.  
Single line telephones,  
answering machines &  
modems  
RJ-45 (wired to TIA T568A standard)  
Ethernet (both 10BaseT and 100BaseT)  
Structured wiring of phones and data lines  
(There are other wiring standards. For  
residential use, we recommend that RJ-45  
jacks be wired to the T568A standard.)  
CAT-5 jumper  
(included)  
Wiring a 110 connector  
110 punch down tool  
elepEntry Module (surge,disconnect)  
ChannelPlus model H612  
H612  
The 110 is a sophisticated insulation  
displacement connection system. To  
push the wire between the contact  
blades, use only a 110 punch down  
tool. Using a screwdriver or needle  
nose pliers may not seat the wire  
properly and can damage the contacts.  
From NTE  
Line 2  
Keep sheath close to connector  
Untwist .5” max.  
1
2
3
6
5
4
Disconnect  
Out  
Surge  
Warnin
Expansion  
Output  
Telephone  
Output  
In  
Line 2  
2
2
3
5
Line 1  
6
5
4
1
2
1
2
3
5
From telephone  
company exchange  
2 lines  
Line 1  
Note order of colors  
2 lines to telephone  
wall plates.  
Wiring a Cat-5 jack  
H618 telephone  
expansion hub  
2
1
3
Telephone Expansion Hub (4 lines x 8 phones)  
ChannelPlus model H618  
110 puunch-  
down tool  
Line  
2
1
2
3
Expansion  
Ports  
Telephones  
5
Line  
R
T
4
In  
2
3
5
Keep sheath  
close to jack.  
R
T
3
2
1
R
T
Use self adhesive  
sticker provided to  
label the output I.D.  
Out  
Follow color code for T568A jacks.  
R
T
Position first pair to channel closest  
to end of jack. (Do not untwist  
conductor pairs more than 0.5"  
from the termination point.)  
Using a 110 punch-down tool,  
push wires into channels and trim.  
Repeat for subsequent pairs.  
When all conductor pairs are  
terminated, snap on strain relief caps.  
Colors of OpenHousetm wiring  
Wiring Modular Plug (T568A)  
Use CAT-3 or CAT-5  
wires, 2 lines to 8  
telephone wall  
1
4
CAT-5, 4 UTP  
RG-6 coax  
2
5
3
6
Telephone  
(from telco)  
Insert wires in this order:  
White/Green  
Green  
White/Orange  
Blue  
Telephone  
(in house)  
Downstream/External  
(to TVs)  
White/Blue  
Orange  
White/Brown  
Brown  
Data  
1
2
4
5
3
6
Security  
Upstream/Internal  
(from modulators)  
 

Blaupunkt Car Stereo System Verona C51 User Manual
Bostitch Air Compressor BTFP02006 User Manual
Bradford White Corp Water Heater 50T65FBN User Manual
Braun Electric Shaver P40 User Manual
Briggs Stratton Pressure Washer 100000 User Manual
Broan Stove RMIP33 User Manual
Brother Label Maker PT 1700 User Manual
Canon Outboard Motor 430 User Manual
Chaney Instrument Weather Radio 06006RM 1036RX User Manual
Chicago Pneumatic Network Card CS7000 User Manual