WML 15040 KL WML 15060 E WML 15080 P
WML 15050 KL WML 15080 DL WML 15100 P
WML 15060 KL WML 15080 DB WML 15100 DB
Washing
1
Machine
6
|
User’s
4
Manual
3
5
Control Panel
Program selection knob
Program follow-up indicator
On / Off button
Start/Pause/Cancel button
Auxiliary function buttons
6
Spin speed selection knob
2
Program Selection and Starting Machine
Plug your machine to outlet. Turn on the machine by pressing
“On / Off” key. Open the door by pulling the handle and load the
1
related to selected program. If you are using auxiliary function
press desired auxiliary function key.
machine without exceeding loading capacity and close the door. Afterwards place appropriate detergent and softener to your
Specify the appropriate program by looking at program selec- machine’s detergent drawer. Start your machine by pressing
tion table according to type of laundry, degree of soiledness and Start/Pause/Cancel button. Start/Pause/Cancel key’s led will be
washing temperature. Position program selection key to desired
washing program-temperature. Select convenient spin speed
on. After your machine starts, you can follow from the program
progress display at which step your machine is.
Program selection table
Program
Cottons 90
Type of laundry
Heavily soiled, heat resistant cotton, linen
Normally soiled, heat resistant cotton, linen
Lightly soiled or heat sensitive cotton
Lightly soiled or heat sensitive cotton
Heavily soiled or heat sensitive cotton
5
5
5
5
5
155 45
145 45
150 45
110 45
180 45
1.70
•
•
•
•
•
•
•
•
(1)
(2)
Cottons 60 *
Cottons 40
Cold (Cotton)
Super 40
0.95 / 1.14
•
•
•
•
•
•
•
0.65
0.35
0.65
Synthetics 60
Normally soiled, heat resistant cotton/synthetic mixture
2.5 120 55
2.5 125 55
0.90
0.55
•
•
•
•
•
•
•
•
Synthetics 40
Synthetics 30
Lightly soiled or heat sensitive cotton/synthetic mixture
Slightly soiled or heat sensitive cotton/synthetic mixture
2.5 110 55
2.5 100 55
0.35
0.20
•
•
•
•
•
•
•
•
Cold (Synthetic) Slightly soiled or heat sensitive cotton/synthetic mixture
Delicates 30
Delicate, sensitive sysnthetic and cotton mixture
2
85
60
0.40
•
•
•
Wool 40
Delicate mixtures with wool and machine washable label
Delicate mixtures with wool and machine washable label
1.5
1.5
1
75
70
55
60
60
50
0.40
0.04
0.21
•
•
•
•
•
•
•
Cold (Wool)
Special program for silks, cashmeres and clothes with not machine washable
labels
Hand Wash 30
Mini 30
Special program for slightly soiled and little amounts of laundry (tracking suits, towels, etc.,
that were used only 1 time)
2.5
30
40
0.16
•
Rinse
Rinsing Program
5
5
23
14
15
-
0.04
0.03
•
•
Spin + Pump
Spinning + Pumping Program
* Energy Labeling Program (EN 60456)
(1)WML15060E-WML15080DB-WML15080P-WML15100P-WML15100DB
( 2 ) WML 15060 KL - WML 15050 KL - WML 15040 KL - WML 15080 DL
-1- EN
Changing Program
Spin Speed selection knob: With the models that contain a
speed selection knob, you can spin your laundries until 1200 rpm
by using this knob. Your machine will not spin over 800 rpm in
the synthetic programs and over 600 rpm in the woolen pro-
grams in order to protect your laundries. If you want to take out
your laundries without spinning, turn the speed selection knob to
“No Spin” position.
Even if a new program is selected by changing the position of
program selection knob while your machine is operating, the first
selected program continues to run.In order to change the wash-
ing program, the ongoing program should be cancelled. (See.
Cancelling a program)
In order to change the auxiliary functions while your machine is
operating, you can make any desired changes after pressing the
“Start/Pause/Cancel” button.
Pressing “On/Off”: You can make the machine ready for
program selection by pressing the “On /off” button. When “On/
Off” button is pressed, “Door” LED is on meaning that “door can
be opened”. To turn off the machine, press the “On/Off” button
again.Pressing the “On/Off” button never means that the program
is started.You must press “Start/Pause/Cancel” button in order
the machine starts its program.
If you want to change the spin speed while your machine is
operating, press the “Start/Pause/Cancel” button, select the spin
speed and press the “Start/Pause/Cancel” button again.
Adding laundry
If you want to add laundry to your machine after the washing
program starts, switch the machine to pause mode by pressing
“Start/Pause/Cancel” button. If the water level in the machine
is suitable, the “Door” light on the program follow-up indicator
comes on approximately 2 minutes later and you can open the
door and add laundry. If the “Door” light is not
continuously on at the end of this period, the water level in the
machine is not suitable and you can not add laundry. You can
resume the program by pressing “Start/Pause/Cancel” button
Child-proof lock: “This machine is equipped with a child lock
in order to prevent the program flow to be affected when the
buttons are pressed during washing cycles. In order to enable
the child lock, press and keep pressed the 1st and 2nd auxiliary
function buttons from the left at the same
time for 3 seconds. The light of the 1st
auxiliary function button will flash continu-
again.
ously. After the program completes, it
is necessary to disable the child lock in
order to initiate a new program or interfere
Canceling a Program
the program. Therefore, when the same
In order to cancel the selected program, “Start/Pause/Cancel”
button is pressed for 3 seconds and machine starts to drain at
the end of this time. Meanwhile, “Washing” and “End” lights are
on. After the drainage process completes “Start/Pause/Cancel”
and “Washing” lights are off. “Door” light starts to flash. When the
“Door” light is on continuously, the door
buttons are pressed for 3 seconds, light of
the second auxiliary function will go off.
Function Selection: Depending on the selected program, the
selectable auxiliary functions are selected by pressing the each
function’s button. The light of the selected function comes on.
Since it is not possible to select some of the auxiliary func-
tions together, one of them becomes off when the other one is
can be opened and a new program can
be selected. You can start a program
by selecting a new program.
The selected program continues to run
selected.
even if the position of program selection
knob is changed while your machine is
Program Progress
operating. In order to change the wash-
After the machine starts to operate, the related light in the program
follow-up indicator comes on according to the selected program.
When a step is complete, the light of the previous step goes off
and the light of the related step comes on. When On/Off button is
pressed, the “Door” light comes on.After the washing program is
selected, “Washing” light on the program follow-up indicator comes
on when the “Start/Pause/Cancel” button is pressed.When the
program ends “End” light comes on. After the program is complete,
the
machine will not allow you to open the door for a while for your
safety. If you want to open the door meanwhile, the door will not
open and the “Door” light will flash. After the door lock is deactivat-
ed the “Door” and “End” lights will come on. Now you can open the
front door. You can switch your machine in to the “Pause” mode by
pressing the “Start/Pause/Cancel” button while your machine is
operating.In this case, “Start/Pause/Cancel” light will flash. You can
make some changes in the program settings in the Pause mode
(See. Changing the Program) and you may also benefit from the
laundry addition function if the “Pause” mode is selected at a
suitable step of the program (See. Laundry addition function).In
order to return to the “Washing” mode from the “Pause” mode,
you need to press the “Start/Pause/Cancel” button again. In this
case, “Start/Pause/Cancel” light will flash and your machine will
resume its program.
ing program, a new program can be
selected and started after “Cancelling a program” by pressing the
“Start/Pause/Cancel” button for 3 seconds as described above.
End of Program
When the program ends “End” light on the program follow-up
indicator comes on. “End” and “Door” lights come on within two
minutes after the door is opened, the machine becomes ready for
the next washing. If any of the buttons is pressed or the posi-
tion of the selection knob is changed when the machine is at the
end of a program, “End” light goes off and only the “Door” light
remains on. Meanwhile, if the door is still locked, the “Door” light
flashes until the door is opened. To turn the machine off, press
the “On/Off” button.
Emptying Laundry
Your machine stops automatically when the program ends. Turn
off the taps. Grab and pull the handle to open the door. Press
“On/Off” button to turn off your machine. After you take the laun-
dries out, leave the front door open and ventilate the inside of the
machine. Check the inside of the bellows and wipe it.
Care and maintanence
5
Detergent Dispenser
Powder detergent residue may accumulate in drawer after a
while. In order to clean detergent drawer press the marked
point of the siphon on softener compartment and push the
drawer towards yourself. Wash the drawer with water
Siphon
Do not neglect cleaning suction cup when it becomes soiled. Water Inlet Filters
In order take suction cup out first take detergent drawer out. Thereisafilterateachflatendwherewaterinlethoseiscon-
Cleanitinordertoeliminateblockingbysoftenerresidue.After nected to tap and at each of water inlet valve placed behind
cleaning place suction cup to its place and make sure it is
placed properly.
themachine. Thesefiltersblocksentranceofforeignobjects
anddirtstothemachine. Filtersmustbecleanedregularlyto
avoidclogging.Fordoingthis,turnofftapwater.Pulloutwater
-3- EN
inlet hoses. Clean the top of the water inlet valve filter with a machine with transportation locks.
brush.Iffiltersareextremelycloggedyoucanpullitoutwitha
pincer.Youcantakeouttheflatsideofwaterinlethoseswithits
seal and clean with tap water.
2. Leveling the feet
In order to operate your machine without
noise and vibration it must be properly on
balance. Four feet of your machine can be
adjusted. First loosen the plastic counter
bolt.Tightenthecounterboltafteradjusting
the feet for leveling your machine.
Hose
Thereisriskoffreezingincoldregion,ifyourmachineisplaced
inacoldplaceremainingwaterinhosesmustbedrainedwith
pumpfilterwhenmachineisnotused.Waterinlethosescanbe
drained by taking it out from tap.
3. Water Connections
a)WaterInletHose:Yourmachineisconnect-
ed to water supply by special hoses supplied
by the machine.
There are plastic seals on hose or plastic bag
for eliminating any leakage in connections
points. These seals must be used on each
side of the connection. Seals on machine side must be con-
nected filter cannal.
Cleaning Pump Filter
• Clean the foreign substance filter
periodically at least for once!
After connecting the hose, check all connections for leaks In
ordertoeliminateanyriskduetowaterleakagekeepthetaps
off when machine is not used.
•Iftheforeignsubstances(coins,buttons,babysocksand
etc.) clog the foamy water pump, clean the filter.
•Beforecleaning,emptythewaterthatremainsinsidefirst.
• Hot water danger: There may be 15 liters of hot water at
90°C in the machine. Open the filter carefully.
Your machine will operate efficiently if the water from tap is
minimum 1 and maximum 10 bars. Practically 1 bar means 8
liters of water in one minute when tap is fully on.
Connecthosetothemachine.Tightenboltswithhandpower,
do not use spanner.
Donotconnectsingleinletmachinetohotwater.Ifmachineis
connectedwithYparttoadoubleinletandover40˚Cforsingle
inlet machines, machine may switch to protection mode.
Drain the water completely in the following situations...
• before cleaning the foreign substance filter;
•beforetransportingthemachine(forexamplemovinginto
a new house);
• when there is a risk of freezing.
1.Turnofftheappliance,unplugthepowercableandclose
thetap.Waitforthehotsoapywatertocoolenough.Other-
wise, there is a risk of scalding.
b) Water drain hose: Water drain hose could be placed either
at the side of the bath tub, or directly to the drain. The hose
should not be bent. Water drain hose should be secured with
the holder so that it would not fall down on the ground.
Thehoseshouldbeplacedbetween40and100cm. fromthe
ground.Waterdrainhosecouldbeplaceddirectlytothedrain
water inlet.
2. Open the service cover by pressing the button. In order
topreventthelittleamountofwaterthatisinsidepumpspill-
ingoverthefloor,putacontainerinfrontofthefiltercover.
Take out the filter by turning anticlockwise.
3. To loosen the foreign substance filter, turn it half turn
(anticlockwise)andtaketheremainingwaterwithacloth.
Whenthereisnowater,turntheforeignsubstancefilteruntil
it is totally released and take it out.
4. Electrical connection
Connect the power cord to the appropirate electrical system
whichisbeingsupportedbythemaximumvoltageandcurrent
rating indicated on the rating plate placed on the washing
machine.
Look! Page 1, Steps before operating Fullautomatic Wash-
ingMachineandsafetyprecautions. Makesurethatyouhave
grounded power outlet.
4. Clean the foreign substance filter and pump opening.
5. Reinstall the foreign substance filter and turn it tightly
(clockwise).
6. Close the service cover.
Before calling service
You turned the machine on, but the leds are off on the
panel.
7
Check the grounding on the power cable or a blown fuse.
Check the front door proper closure.
Machine does not take water.
Checkthefrontdoorforproperclosure.Eithertapsareclosed
or water intake filters are clogged.
Taken water is directly discharged.
Check if the discharge hose placed as described in the users
Installation
1. Removing the transportation safety bolts
Beforethewashingmachineisoperated,thetransitbarsmust
be removed! In order to do this:
6
manual or not.
Water coming from beneath the machine.
Checkthewaterintakeanddrainhoses.Tightentheconnec-
tions.Thewashersofthehosesmaybewornout.Ifnonofthe
both, the pump filter is not closed properly.
Foam coming out of the detergent dispenser.
Check whether your detergent is suitable for automatic ma-
chines. Next time use less detergent.
1.Loosen“C”boltsbyrotatingthemcounterclockwisewitha
suitable spanner
Pump does not drain water.
2. Remove transportation safety bolts by turning.
3.Place“P”plasticcoversontotheopeningsoftransportation
locks by rotating in direction of arrow and pushing.
Attentionplease!Keepthetransitsafetyboltsforusingwhen
machine is to be transported again. Always transport your
Cleanthepumpfilter.Checkwhetherthedrainhoseisbentor
not.Ifthereisneedtocleanthepumpfilter,refertothepump
filter cleaning section of the manual.
-4- EN
|