BOXLIGHT Projector CP 33t User Manual

USER’S GUIDE  
BOXLIGHT CP-33t  
BOXLIGHT  
®
 
IMPORTANT SAFETY INSTRUCTIONS  
All the safety and operating instructions should be read before  
the product is operated.  
d. If the projector does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the projector to normal operation.  
Read all of the instructions given here and retain them for later  
use. Unplug this projector from AC power supply before  
cleaning. Do not use liquid or aerosol cleaners. Use a damp  
cloth for cleaning.  
e. If the projector has been dropped or the cabinet has been  
damaged.  
Do not use attachments not recommended by the  
manufacturer as they may cause hazards.  
f. When the projector exhibits a distinct change in  
performance-this indicates a need for service.  
Do not place this projector on an unstable cart, stand, or table.  
The projector may fall, causing serious injury to a child or  
adult, and serious damage to the projector. Use only with a  
cart or stand recommended by the manufacturer, or sold with  
the projector. Wall or shelf mounting should follow the  
manufacturer's instructions, and should use a mounting kit  
approved by the manufacturer.  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer that have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock, or injury to persons.  
Upon completion of any service or repairs to this projector, ask  
the service technician to perform routine safety checks to  
determine that the projector is in safe operating condition.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool, etc...  
This projector is equipped with a  
grounding type AC line plug.  
Should you be unable to insert the  
plug into the outlet, contact your  
electrician. Do not defeat the  
Slots and openings in the back and bottom of the cabinet are  
provided for ventilation, to insure reliable operation of the  
equipment and to protect it from overheating.  
The openings should never be covered with cloth or other  
materials, and the bottom opening should not be blocked by  
placing the projector on a bed, sofa, rug, or other similar  
surface. This projector should never be placed near or over a  
radiator or heat register.  
safety purpose of this grounding  
type plug.  
GROUND  
Follow all warnings and instructions marked on the projectors.  
For added protection to the projector during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet. This will prevent damage  
due to lightning and power line surges.  
This projector should not be placed in a built-in installation  
such as a book case unless proper ventilation is provided.  
This projector should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supplied, consult your authorized dealer or  
local power company.  
An appliance and cart combination  
should be moved with care. Quick  
stops, excessive force, and uneven  
surfaces may cause the appliance  
and cart combination to overturn.  
Do not overload wall outlets and extension cords as this can  
result in fire or electric shock. Do not allow anything to rest on  
the power cord. Do not locate this projector where the cord  
may be damaged by persons walking on it.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the projector.  
If the projector is to be built into a compartment or similarly  
enclosed, the minimum distances must be maintained.  
Do not cover the ventilation slot on the projector.  
Heat build-up can reduce the service life of your projector, and  
can also be dangerous.  
Do not attempt to service this projector yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
20cm  
Unplug this projector from wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
WALL  
PROJECTOR  
(FRONT)  
PROJECTOR  
(SIDE)  
c. If the projector has been exposed to rain or water.  
50cm  
50cm  
50cm  
3
 
TABLE OF CONTENTS  
FEATURES AND DESIGN  
5
6
COMPUTER MODE  
23  
SELECTING COMPUTER MODE  
SELECTING COMPUTER SYSTEM  
PC ADJUSTMENT  
23  
23  
24  
PREPARATION  
COMPATIBLE COMPUTER SPECIFICATION 26  
NAME OF EACH PART OF THE PROJECTOR  
6
PICTURE IMAGE ADJUSTMENT  
PICTURE POSITION ADJUSTMENT  
PICTURE SCREEN ADJUSTMENT  
27  
28  
29  
SETTING-UP THE PROJECTOR  
POSITIONING THE PROJECTOR  
ADJUSTABLE FEET  
7
7
7
8
8
9
CONNECTING THE AC POWER CORD  
VENTILATION  
MOVING THE PROJECTOR  
VIDEO MODE  
30  
SELECTING VIDEO MODE  
30  
30  
30  
31  
SELECTING COLOR SYSTEM  
PICTURE SCREEN ADJUSTMENT  
PICTURE IMAGE ADJUSTMENT  
CONNECTING THE PROJECTOR 10  
TERMINALS OF THE PROJECTOR  
CONNECTING TO THE VIDEO EQUIPMENT  
CONNECTING TO THE COMPUTER  
10  
11  
12  
MCI MODE  
32  
OPERATING THE PC CARD SLOT  
SELECTING MCI MODE  
SHOW THE DATA IN THE MEMORY CARD  
WRITE DATA INTO THE MEMORY CARD  
PICTURE IMAGE ADJUSTMENT  
PICTURE POSITION ADJUSTMENT  
PICTURE SCREEN ADJUSTMENT  
SMART MEDIA AND PC CARD ADAPTER  
32  
33  
34  
35  
36  
36  
37  
38  
BEFORE OPERATION  
14  
OPERATION OF THE REMOTE CONTROL  
LASER POINTER FUNCTION  
14  
14  
15  
REMOTE CONTROL BATTERIES INSTALLATION  
TOP CONTROLS AND INDICATORS  
16  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE THE ON-SCREEN MENU  
FLOW OF ON-SCREEN MENU  
MENU BAR  
17  
17  
17  
18  
SETTING  
40  
SETTING MENU  
SETTING LANGUAGE  
40  
40  
BASIC OPERATION  
20  
TURNING ON / OFF THE PROJECTOR  
20  
ADJUSTING THE IMAGE  
ZOOM ADJUSTMENT  
21  
21  
21  
21  
22  
22  
APPENDIX  
41  
FOCUS ADJUSTMENT  
KEY STONE ADJUSTMENT  
NO SHOW FUNCTION  
OPERATING WIRELESS MOUSE  
MAINTENANCE  
41  
42  
42  
42  
42  
43  
43  
PICTURE FREEZE FUNCTION  
TEMPERATURE WARNING INDICATOR  
AIR FILTER CARE AND CLEANING  
CLEANING THE PROJECTION LENS  
LAMP REPLACEMENT  
SOUND ADJUSTMENT  
SOUND VOLUME ADJUSTMENT  
SOUND MUTE ADJUSTMENT  
22  
22  
22  
LAMP REPLACEMENT MONITOR TIMER  
TROUBLESHOOTING  
TECHNICAL SPECIFICATIONS  
44  
46  
TRADEMARKS  
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.  
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.  
Windows and PowerPoint are registered trademarks of Microsoft Corporation.  
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its  
respective corporation.  
4
 
FEATURES AND DESIGN  
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of  
use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal  
display (LCD) technology.  
Compatibility  
PC CARD SLOT  
This projector is compatible with many different  
types of personal computers and video  
devices, including;  
This projector has a PC CARD SLOT for  
easier presentations. Pictures can be  
projected just by inserting a memory card  
including image data. Presentation data can  
be edited by "Media Card Imager" software  
(supplied). Refer to the pages 32 ~ 39 of this  
manual and the Owners Manual for Media  
Card imager for operations.  
IBM-compatible computers, including  
laptops, up to 1280 x 1024 resolution.  
Apple Macintosh and PowerBook  
computers up to 1280 x 1024 resolution.  
Various video equipment using any of the  
world wide video standards, including  
NTSC, NTSC4.43, SECAM, PAL, PAL-M  
and PAL-N.  
Laser Pointer Function  
The Remote Control Unit of this projector  
includes the Laser Pointer function providing  
convenience for your presentations.  
Image Resolution  
Picture Image of the computer is projected in  
the resolution of 1024 x 768 and it is provided  
just as appearing on your computer's monitor.  
Screen resolutions between 1024 x 768 and  
1280 x 1024 are compressed to 1024 x 768,  
and this projector cannot display screen  
resolutions above 1280 x 1024. If your  
computer's screen resolution is higher than  
1280 x 1024, reset it to a lower resolution  
before you connect the projector.  
Other Features  
This projector has Motor Zoom/Focus, No  
Show, Picture Freeze, Keystone, Mute  
functions and a Air Pad Remote Control.  
Accessories  
This projector comes with the parts listed  
below. Check to make sure all are included. If  
any part is missing, contact Boxlight  
immediately.  
Owner's Manual.  
AC Power Cord.  
Wireless Remote Control Unit.  
Batteries for Remote Control Unit.  
VGA Cable.  
Portability  
This projector is quite compact in size and  
weight. Having a sophisticated shape like an  
attaché case with a retractable carrying handle,  
the projector will help you make powerful  
presentations wherever you go.  
Automatic Multiscanning System  
Control Cable for PS/2 Port.  
Media Card Imager for Windows 95 (CD-ROM)  
and Owners Manual for this software.  
SmartMedia and PC Card Adapter.  
Lens Cover.  
This projector automatically tune to the most  
personal computers currently distributed by  
simply connecting. It is free from complicated  
adjustments to project picture images from  
most personal computers.  
Dust Cover.  
Multilanguage Menu Display  
Operation menu is displayed in; English,  
Deutsch, Français, Italiano, Español, or  
Japanese  
5
 
PREPARATION  
NAME OF EACH PART OF THE PROJECTOR  
FRONT OF THE CABINET  
PROJECTION LENS  
PC CARD SLOT  
LENS COVER  
CARRY HANDLE  
INFRARED REMOTE RECEIVER  
SPEAKER (Monaural)  
BACK OF THE CABINET  
EXHAUST VENT  
HOT AIR EXHAUSTED !  
Air blown from the exhaust vent is hot.  
When using or installing the projector, the  
following attention should be taken.  
Do not put a flammable object near this  
vent.  
Keep heat-sensitive objects away from the  
exhaust vent.  
Do not touch this area especially screws  
and metallic parts. This area will become  
hot while the projector is used.  
INFRARED  
REMOTE RECEIVER  
POWER CORD CONNECTOR  
BOTTOM OF THE CABINET  
AIR INTAKE VENTS  
These Air Intake Vents  
should not be blocked.  
ADJUSTABLE FEET  
AND  
FEET LOCK LATCHES  
LAMP COVER  
6
 
PREPARATION  
SETTING-UP THE PROJECTOR  
POSITIONING THE PROJECTOR  
This projector is designed to project on a flat projection surface.  
The projector can be focused from 4.6(1.4m) ~ 35.4(10.8m).  
Refer to the figure below to adjust the screen size.  
35.4(10.8m)  
24.0(7.3m)  
200”  
300”  
18.0(5.5m)  
11.8(3.6m)  
150”  
231”  
4.6(1.4m)  
100”  
H1  
H2  
154”  
115”  
40”  
77”  
30”  
30”  
60”  
100”  
150”  
200”  
300”  
Screen Size  
(W x H) mm  
610 x 457  
1219 x 914  
34.3(870mm)  
1.7(44mm)  
2032 x 1524  
3048 x 2286  
4064 x 3048  
6096 x 4572  
17.1(435mm)  
0.9(22mm)  
57.1(1451mm) 85.7(2177mm) 114.3(2903mm) 171.4(4354mm)  
2.9(73mm) 4.3(109mm) 5.7(145mm) 8.6(218mm)  
Height (H1)  
Height (H2)  
ROOM LIGHT  
The brightness in the room has a great influence on the picture quality. It is recommended to limit ambient  
lighting in order to provide the best image.  
ADJUSTABLE FEET  
Picture tilt and projection angle can be adjusted by  
rotating the ADJUSTABLE FEET. Projection angle can  
be adjusted to 10 degrees.  
Lift the front of the projector and pull the FEET LOCK  
LATCHES on both sides of the projector.  
1
Release the FEET LOCK LATCHES to lock the  
ADJUSTABLE FEET and rotate the ADJUSTABLE  
FEET to fine tune the position and the tilt.  
2
To shorten the ADJUSTABLE FEET, lift the front of the  
projector and pull and undo the FEET LOCK LATCHES.  
3
FEET LOCK  
LATCHES  
The position and the keystone distortion of the image  
can also be adjusted using the Menu Operation. (Refer  
to pages 21, 29, 30 and 37.)  
ADJUSTABLE FEET  
7
 
PREPARATION  
CONNECTING THE AC POWER CORD  
This projector uses nominal input voltages of 100-120V  
AC or 200-240V AC. The projector automatically  
selects the correct input voltage. It is designed to work  
with single-phase power systems having a grounded  
neutral conductor. To reduce the risk of electrical  
shock, do not plug into any other type of power system.  
Consult your authorized dealer or service station if your  
are not sure of the type of power supply being in use.  
Connect the projector with the peripheral equipment  
before turning the projector on. (Refer to pages 10 ~ 13  
for connection.)  
Connect the AC power supply cord (supplied) to the  
projector.  
The socket-outlet must be near this equipment and  
must be easily accessible.  
CAUTION  
For safety, unplug the AC Power Cord when the  
appliance is not in use.  
When this projector is connected to the outlet with  
the AC Power Cord, the appliance is in Stand-by  
Mode and consumes some electric power.  
AC outlet side (Male)  
Projector side (Female)  
VENTILATION  
This projector is equipped with cooling fans for protection from overheating. Pay attention to the following to  
ensure ventilation and avoid a possible risk of fire and malfunction.  
Do not cover the vent slot.  
Keep the rear grill at least 1m (3 feet) away from any  
object.  
Keep sides clear of any obstructions. Obstructions  
EXHAUST VENT  
(REAR SIDE)  
may block cooling air.  
AIR INTAKE VENTS  
(BOTH SIDES)  
8
 
PREPARATION  
MOVING THE PROJECTOR  
Use the Carry Handle when moving the Projector.  
When moving the projector, replace the Lens Cover and  
retract the Adjustable Feet to prevent damage to the lens and  
cabinet.  
When this projector is not in use for an extended period,  
replace the Lens Cover, retract the Adjustable Feet and apply  
the Dust Cove0r supplied with this projector.  
CAUTION WHEN CARRYING OR TRANSPORTING THE PROJECTOR  
Do not drop or bump the projector, otherwise damages or malfunctions may result.  
When transporting the projector, use a carrying case recommended by Boxlight.  
Do not transport the projector by using a courier or transport service in an unsuitable transport case. This  
may cause damage to the projector. To transport the projector through a courier or transport service, use  
a case recommended by Boxlight.  
For carrying or transportation cases, contact a Boxlight at 1-800-762-5757 or 360-779-7901.  
9
 
CONNECTING THE PROJECTOR  
TERMINALS OF THE PROJECTOR  
S-VIDEO INPUT JACK  
VIDEO INPUT JACK  
Connect the S-VIDEO output  
from the video equipment to this  
terminal.  
Connect the video output from  
the video equipment to this  
terminal.  
(Refer to P11.)  
S-VIDEO  
(Refer to P11.)  
AUDIO INPUT JACKS  
COMPUTER AUDIO INPUT JACK  
AUDIO  
IN  
Connect the audio outputs from  
the video equipment to these  
terminals.  
R-AUDIO-L(MONO)  
VIDEO  
Connect the audio output from  
the computer to this terminal.  
(Refer to P12, 13.)  
OUT  
(Refer to P11.)  
COMPUTER IN  
MONITOR OUT  
When the audio output is  
monaural, connect it to the Left  
jack.  
AUDIO OUTPUT JACK (STEREO)  
Connect the audio amplifier to  
this terminal.  
(Refer to P12, 13.)  
CONTROL PORT  
COMPUTER INPUT TERMINAL  
Connect the computer output to  
this terminal.  
(Refer to P12, 13.)  
CONTROL PORT CONNECTOR  
When controlling the computer  
with the Remote Control of this  
projector, connect the mouse  
port of your personal computer  
to this terminal. It is also used  
for write on or read from the  
data of the PC CARD SLOT in  
MCI mode.  
MONITOR OUTPUT TERMINAL  
This terminal outputs the signal  
from the COMPUTER IN  
terminal. Connect to the monitor  
to this terminal.  
(Refer to P12, 13.)  
(Refer to P12, 13, 35.)  
COMPUTER INPUT / MONITOR OUTPUT TERMINAL  
Terminal : HDB15-PIN  
Connect the display output terminal of the computer to COMPUTER INPUT with the VGA Cable (supplied). And connect  
the monitor to MONITOR OUTPUT with the monitor cable (not supplied). When connecting the Macintosh computer, the  
MAC Adapter (not supplied) is required.  
1
2
3
4
5
6
7
8
Red Input  
Green Input  
Blue Input  
Sense 2  
9
Non Connect  
Pin Configuration  
10 Ground (Vert.sync.)  
11  
12  
Sense 0  
Sense 1  
Horiz. sync.  
Vert. sync.  
Reserved  
2
1
5
4
3
10  
9
8
7
6
Ground (Horiz.sync.) 13  
Ground (Red)  
Ground (Green) 15  
Ground (Blue)  
15  
14  
13  
12  
11  
14  
CONTROL PORT CONNECTOR  
Terminal : Mini DIN 8-PIN  
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (the Control  
Cable for PS/2 port is supplied).  
PS/2  
-----  
CLK  
DATA  
GND  
-----  
-----  
GND  
-----  
Serial  
R X D  
-----  
-----  
GND  
RTS  
T X D  
GND  
GND  
ADB  
-----  
ADB  
-----  
GND  
-----  
-----  
Pin Configuration  
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
-----  
GND  
10  
 
CONNECTING THE PROJECTOR  
CONNECTING TO THE VIDEO EQUIPMENT  
Video Source (example)  
Video Cassette Recorder  
Video Disc Player  
Video / Audio Output  
S-VIDEO Output  
Used cables for connection  
VIDEO CABLE ●  
S-VIDEO CABLE ●  
AUDIO CABLE (stereo) ●  
Use either the VIDEO jack  
or the S-VIDEO jack.  
When the both jacks are  
connected, the S-VIDEO  
jack has priority over the  
VIDEO jack.  
These cables are not supplied  
with this projector.  
Video Audio Cable ●  
S-VIDEO Cable ●  
Terminals  
of the Projector  
S-VIDEO  
AUDIO  
IN  
R-AUDIO-L(MONO)  
VIDEO  
OUT  
COMPUTER IN  
MONITOR OUT  
CONTROL PORT  
Audio Cable (Stereo) ●  
Audio Input  
External Audio Equipment  
NOTE :  
When connecting the cables, the power cords of  
both the projector and the external equipment  
should be disconnected from AC outlet. Turn the  
projector and peripheral equipment on before the  
computer is switched on.  
Audio Speaker  
(stereo)  
Audio Amplifier  
11  
 
CONNECTING THE PROJECTOR  
CONNECTING TO THE COMPUTER  
To connect to the computer, refer to the figure below.  
Used cables for connection  
VGA CABLE  
CONTROL CABLE FOR PS/2 PORT  
CONTROL CABLE FOR SERIAL PORT,or ADB PORT ●  
MAC ADAPTER ●  
MONITOR CABLE ●  
PC AUDIO CABLE (stereo) ●  
These cables are not supplied with this projector.  
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)  
Desktop type  
Laptop type  
Monitor  
Audio Speaker  
(stereo)  
Audio Amplifier  
Audio Input  
To each terminal of your computer  
To the Monitor  
Monitor Output  
Serial port PS/2 port  
ADB port Audio Output  
MAC Adapter ●  
Set the slide  
ON  
DIP  
switches following  
the chart on the  
next page.  
1
2
3
4
5
6
Terminal  
Terminal  
Terminal  
Audio Cable (stereo) ●  
Control Cable for ADB Port ●  
Control Cable for PS/2 Port  
Control Cable for Serial Port ●  
VGA Cable  
Monitor Cable ●  
NOTE :  
When connecting the cable, the power cords of both the projector and the external equipment should be disconnected  
from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.  
12  
 
CONNECTING THE PROJECTOR  
S-VIDEO  
AUDIO  
IN  
R-AUDIO-L(MONO)  
VIDEO  
OUT  
COMPUTER IN  
MONITOR OUT  
CONTROL PORT  
COMPUTER  
IN  
MONITOR  
OUT  
CONTROL  
PORT  
AUDIO  
IN  
AUDIO  
OUT  
MAC ADAPTER (Not supplied)  
Set the switches as shown  
in the table below depend-  
ing on the RESOLUTION  
MODE that you want to  
use before your turn on the  
projector and computer.  
ON  
Use one of these Control  
ON  
DIP  
Cables corresponding  
with the terminal of your  
computer.  
1
2
3
4
5
6
OFF  
2
1
3
4
5
6
13" MODE (640 x 480)  
ON  
ON OFF OFF OFF OFF  
16" MODE (832 x 624) OFF ON OFF ON OFF OFF  
19" MODE (1024 x 768) OFF ON  
21" MODE (1152 x 870) ON ON  
ON OFF OFF OFF  
ON ON OFF OFF  
13  
 
BEFORE OPERATION  
OPERATION OF THE REMOTE CONTROL  
VIDEO BUTTON  
Used to select VIDEO  
source. (P30)  
POWER ON-OFF BUTTON  
Used to turn the projector on  
or off. (P20)  
Left Side  
COMPUTER/  
MCI  
ON-OFF  
VIDEO  
ZOOM FOCUS  
VOLUME  
COMPUTER / MCI BUTTON  
Used to select source either  
COMPUTER or MCI mode.  
(P23, 33)  
D.ZOOM  
MUTE  
PAGE  
POINT BUTTON  
MENU BUTTON  
Used to select MENU  
operation. (P17-19)  
Used to move the pointer on  
the MENU, to adjust the item,  
or to pan the image in DIGITAL  
ZOOM mode. (P29, 37)  
MENU  
It is also used as a PC mouse  
in Wireless Mouse Operation.  
(P41)  
SELECT BUTTON  
When pressing the center of this  
button, it works as the SELECT  
button.  
Used to execute the item  
selected or to expand the  
image in DIGITAL ZOOM  
mode. (P29, 37)  
It is also used as a PC mouse  
in Wireless Mouse Operation.  
(P41)  
LASER  
RIGHT CLICK BUTTON  
ALL-OFF SWITCH  
KEYSTONE  
NO SHOW  
Used to compress the image  
in DIGITAL ZOOM mode.  
(P29, 30, 37)  
When using the Remote Control  
Unit, turn this switch to ONand  
turn it ALL OFFwhen it is not  
used.  
FREEZE  
It is also used as a PC mouse  
in Wireless Mouse Operation.  
(P41)  
AUTO IMAGE  
NORMAL  
LASER BUTTON  
Used to operate laser pointer  
function. The laser beam is  
emitted while pressing this  
button (within 1 minute).  
When using the laser pointer  
for more than  
1
minute,  
release the button and press it  
again.  
LASER POINTER FUNCTION  
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window. When the LASER button is  
pressed, the laser light goes on. And when the button is pressed more than 1 minute or the button is released, light goes off.  
Laser light is emitted with the RED light which tells the laser beam being emitted.  
The laser emitted is a class II laser; therefore, do not look into the Laser Light Window or shine the laser beam on yourself or  
other people. The three labels or marks below are the caution labels for the laser beam.  
CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result in  
hazardous radiation exposure.  
These caution labels are put on the remote control.  
Laser Light Window  
14  
 
BEFORE OPERATION  
Operating Range  
VOLUME BUTTON  
Used to adjust volume.  
(P22)  
COMPUTER/  
MCI  
ON-OFF  
Point the remote control toward the  
projector (Receiver Window) when  
pressing the buttons. Maximum  
operating range for the remote  
control is about 16.4(5m) and 60°  
front and rear of the projector  
VIDEO  
ZOOM BUTTON  
Used to adjust zoom.  
(P21)  
ZOOM FOCUS  
VOLUME  
D.ZOOM BUTTON  
Used to turn the projector  
into DIGITAL ZOOM  
mode. (P29, 37)  
FOCUS BUTTON  
Used to adjust focus.  
(P21)  
D.ZOOM  
MUTE  
MENU  
PAGE  
PAGE BUTTONS  
Used to move to next /  
previous page of the data  
in memory card. These  
buttons are activated in  
MCI mode only. (P34)  
60°  
MUTE BUTTON  
Used to mute sound.(P22)  
16.4’  
(5 m)  
FREEZE BUTTON  
Used to freeze the picture.  
(P22)  
LASER  
NO SHOW BUTTON  
Used to turn the picture  
into a black image. (P22)  
KEYSTONE  
NO SHOW  
FREEZE  
NORMAL BUTTON  
Used to reset to normal  
picture adjustment preset  
by the factory.  
AUTO IMAGE  
NORMAL  
AUTO IMAGE BUTTON  
Use to operate AUTO  
IMAGE function. (P28)  
16.4’  
(5 m)  
(P27, 31, 36)  
60°  
KEY STONE BUTTON  
Used to correct the key  
stone distortion.  
(P21, 29, 30, 37)  
REMOTE CONTROL BATTERIES INSTALLATION  
Remove the battery  
compartment lid.  
Slide the batteries into the  
compartment.  
Replace the compartment  
lid.  
1
2
3
Press the lid down-  
ward and slide it.  
Two AA size batteries  
For correct polarity (+  
and ), be sure the  
battery terminals are in  
contact with the pins in  
the compartment.  
To insure safe operation, please observe the following precautions :  
Use (2) AA, UM3 or R06 type alkaline batteries.  
Replace two batteries at the same time.  
Do not use a new battery with a used battery.  
Avoid contact with water or liquid.  
Do not expose the Remote Control Unit to moisture, or heat.  
Do not drop the remote control unit.  
If batteries have leaked on the remote control, carefully wipe the case clean and install new batteries.  
15  
 
BEFORE OPERATION  
TOP CONTROLS AND INDICATORS  
NORMAL BUTTON  
Used to reset to normal  
picture adjustment preset  
by factory. (P27, 31, 36)  
AUTO IMAGE BUTTON  
PAGE BUTTONS  
Used to operate AUTO  
IMAGE function. (P28)  
Used to move to the next /  
previous page of the data in  
the memory card plugged  
into PC CARD SLOT.  
These buttons are used to  
stop or resume AUTO-  
POWER ONOFF BUTTON  
Used to turn the projector  
on or off. (P20)  
PLAY function.  
Page  
buttons are activated in  
MCI mode. (P34.)  
NORMAL  
PAGE  
VOLUME  
LAMP INDICATOR  
This indicator is dim when  
the projector is turned on.  
And bright when the  
projector is in stand-by  
mode.  
VOLUME BUTTONS  
Used to adjust volume.  
(P22)  
LAMP  
AUTO IMAGE  
MODE BUTTON  
READY  
Used to select input source  
either Computer, Video or  
MCI mode. (P23, 30, 33)  
ONOFF  
MENU  
MODE  
READY INDICATOR  
This indicator is green  
when the projector is ready  
to be turned on.  
WARNING  
TEMP.  
SELECT BUTTON  
SELECT  
Used to execute the item  
selected. It is also used to  
expand the image in  
DIGITAL ZOOM mode.  
(P29, 37)  
WARNING TEMP. INDICATOR  
LAMP  
REPLACE  
This indicator flashes red  
when internal projector  
temperature is too high.  
(P42)  
ZOOM  
FOCUS  
POINT BUTTONS  
Used to select an item and  
adjust the value on the  
MENU. It is also used to  
pan the image in DIGITAL  
ZOOM mode. (P29, 37)  
LAMP REPLACE INDICATOR  
This indicator turns yellow  
when the life of the  
projection lamp draws to an  
end. (P43)  
FOCUS BUTTONS  
Used to select focus adjust.  
(P21)  
MENU BUTTON  
Used to open or close the  
MENU operation.  
(P17, 19)  
ZOOM BUTTONS  
Used to select zoom adjust.  
(P21)  
16  
 
BEFORE OPERATION  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
You can control and adjust this projector through the  
WIRELESS REMOTE CONTROL  
ON-SCREEN MENU. Refer to the following pages to  
operate each adjustment on the ON-SCREEN MENU.  
POINT BUTTON  
Used to move the  
Pointer to UP/ DOWN/  
RIGHT/ LEFT.  
1 MOVING THE POINTER  
Move the pointer (see the NOTE below) by pressing POINT  
button(s) on the TOP CONTROL or the REMOTE CONTROL.  
SELECT BUTTON  
Used to select the item.  
2 SELECT THE ITEM  
TOP CONTROL  
Select the item by pressing SELECT button.  
SELECT BUTTON  
Used to select the item.  
NOTE : Pointer is the icon on the ON-SCREEN Menu to  
select the item. See the figures on the section  
"FLOW OF ON-SCREEN MENU" below.  
SELECT  
POINT BUTTONS  
Used to move the  
Pointer to UP/ DOWN/  
RIGHT/ LEFT.  
FLOW OF ON-SCREEN MENU  
MENU BAR  
Display ON-SCREEN MENU  
Press MENU button to display the ON-SCREEN MENU  
(MENU BAR). The red frame is the POINTER.  
1
POINTER  
(red frame)  
SELECT  
BUTTON  
ITEM ICON  
Select the Item  
Move the POINTER (red frame) to the ITEM ICON that  
you want to select by pressing POINT RIGHT/ LEFT  
buttons.  
2
Select the ITEM by pressing SELECT button. The  
dialog box of the ITEM appears.  
POINTER  
(red frame)  
3
Control and adjust through ON-SCREEN MENU  
MENU  
Move the POINTER downward by pressing POINT  
DOWN button. (The shape of the POINTER becomes  
an arrow.)  
4
POINT  
DOWN  
Move the POINTER to the ITEM that you want to adjust  
and adjust the ITEM by pressing SELECT button.  
Refer to the following pages for details of respective  
adjustments.  
BUTTON  
5
POINTER  
17  
 
BEFORE OPERATION  
MENU BAR  
MENU BAR IN COMPUTER MODE  
Press MENU BUTTON while in Computer mode.  
PC ADJUST MENU  
SETTING MENU  
MODE MENU  
SYSTEM MENU  
POSITION MENU  
Used to adjust the  
parameters to  
match with the input  
signal format.  
Used to set the Display  
Menu and to reset  
Lamp Replacement  
Monitor Timer.  
Used to select  
the Computer  
input mode.  
Used to select a  
computer  
system.  
Used to adjust  
the position of  
the image.  
(Refer to P24, 25)  
(Refer to P40)  
(Refer to P23)  
(Refer to P23)  
(Refer to P28)  
AUTO IMAGE MENU  
IMAGE MENU  
SCREEN MENU  
LANGUAGE MENU  
Used to adjust Fine  
sync., Total dots,  
and Picture Position  
automatically.  
Used to adjust the  
computer image. [Fine  
sync. / Total dots /  
White Balance /  
Contrast / Brightness]  
(Refer to P27)  
Used to adjust  
the size of the  
image.  
Used to select  
the language  
used in the  
Menu.  
(Refer to P29)  
(Refer to P28)  
(Refer to P40)  
MENU BAR IN VIDEO MODE  
MODE MENU  
Press MENU BUTTON while in Video mode.  
IMAGE MENU  
Used to adjust the  
Color /  
Tint / White Balance /  
Contrast / Brightness/  
picture image. [  
Used to select  
the Video input.  
(Refer to P30)  
These icons have the  
same function as in  
the Computer Mode.  
Sharpness  
]
(Refer to P31)  
SYSTEM MENU  
SCREEN MENU  
Used to select a  
color system among  
Used to set the size  
of the image either  
Regular or Wide,  
or to correct the  
PAL, SECAM, NTSC,  
[
NTSC 4.43, PAL-M and  
PAL-N  
].  
(Refer to P30)  
Keystone distortion.  
(Refer to P30)  
18  
 
MENU BAR IN MCI MODE  
Press MENU BUTTON while in MCI mode.  
IMAGE MENU  
MODE MENU  
Used to adjust the  
computer image. [Fine  
sync. / Total dots /  
White Balance /  
Contrast / Brightness]  
(Refer to P36)  
Used to select  
the MCI input  
mode.  
These icons have the  
same function as in the  
Computer Mode.  
(Refer to P33)  
VIEW MENU  
POSITION MENU  
SCREEN MENU  
Used to display, read  
or write the image data  
in a memory card  
through the PC CARD  
SLOT.  
Used to adjust  
the position of  
the image.  
Used to adjust  
the size of the  
image.  
(Refer to P36)  
(Refer to P37)  
(Refer to P34, 35)  
19  
 
BASIC OPERATIONS  
TURNING ON / OFF THE PROJECTOR  
TURNING ON THE PROJECTOR  
Complete the peripheral connections (with Computer, VCR,  
etc.) before turning on the projector. (Refer to "CONNECTING  
TO THE PROJECTOR" on Pages 10~13 for connecting that  
equipment.  
1
Connect the projector's AC power cord into a wall outlet. The  
LAMP indicator lights RED, and the READY indicator lights  
GREEN.  
2
3
30  
Press the power ON-OFF button on the Remote Control Unit or  
on the Top Control to ON. The LAMP POWER indicator dims,  
and the Cooling Fans start to operate. The Preparation Display  
appears on the screen and the count-down starts. The signal  
from the source appears after 30 seconds.  
The Preparation Display disappears after 30 seconds.  
TURNING OFF THE PROJECTOR  
Press the power ON-OFF button on the Remote Control Unit or  
on the Top Control, and the message "Power off?" appears on  
the screen.  
1
2
Power off?  
Press again the power ON-OFF button to turn off the projector.  
The LAMP indicator lights bright and the READY indicator turns  
off. The Cooling Fans operate for 90 seconds after the  
projector is turned off. (During this "Cooling Down" period, this  
appliance cannot be turned on.)  
The message disappears after 4 seconds.  
When the cooling the projector has finished, the READY  
indicator turns to green again and you can turn the projector  
on. After cooling down completely, disconnect the AC power  
cord.  
3
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN IT ON, WAIT AT LEAST 5  
MINUTES BEFORE TURNING IT OFF.  
When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. Wait  
at least 5 minutes before turning the projector on again.  
If the TEMPERATURE WARNING indicator continues to flash, follow procedures below:  
1. Disconnect the AC power cord from the AC outlet.  
2. Check the air filters for dust accumulation.  
3. Clean the Air Filter. (See "AIR FILTER CARE AND CLEANING" section on page 42.)  
4. Press the power ON-OFF button to ON.  
If the TEMPERATURE WARNING indicator still continues to flash, call Boxlight at 1-800-762-5757 or 360-  
779-7901.  
NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling  
Fan is working, TEMPERATURE WARNING INDICATOR flashes red.  
20  
 
BASIC OPERATION  
ADJUSTING THE IMAGE  
ZOOM ADJUSTMENT  
Press the ZOOM button on the Top Control or the ZOOM /●  
button on the Remote Control Unit to turn into the ZOOM  
mode.  
1
2
Press the POINT UP button or the ZOOM button to have the  
image larger, and press the POINT UP button or the ZOOM ●  
button to have the smaller.  
Zoom  
In the Computer mode, the image can be expanded, compressed,  
and panned with the Digital Zoom function. Refer to page 29, 37 for  
the Digital Zoom operation.  
The message disappears after 4 seconds.  
FOCUS ADJUSTMENT  
Press the FOCUS button on the Top Control or the FOCUS  
/button on the Remote Control Unit to turn into the FOCUS  
mode.  
1
2
Adjust the focus of the image by pressing the POINT  
UP/DOWN button or the FOCUS /button.  
Focus  
The message disappears after 4 seconds.  
KEYSTONE ADJUSTMENT  
If the picture has keystone distortion, correct image with KEYSTONE adjustment.  
Press the KEYSTONE /button on the Remote Control Unit  
or select the Keystone on the SCREEN menu. (Refer to page  
29, 30, 37.) The message Keystoneis displayed.  
1
Keystone  
Correct the Keystone distortion by pressing the KEYSTONE  
/button or the POINT UP/DOWN button(s). Press the  
KEYSTONE button or the POINT UP button to reduce the  
upper part or the image, and press the KEYSTONE button or  
the POINT DOWN button to reduce the lower part.  
2
The message disappears after 4 seconds.  
Reduce the upper width with the KEY STONE  
button or the POINT UP button.  
Reduce the lower width with the KEY STONE ●  
button or the POINT DOWN button.  
21  
 
BASIC OPERATION  
NO SHOW FUNCTION  
Press the NO SHOW button on the Remote Control Unit to black out  
the image. This function is cancelled when the NO SHOW button is  
pressed again or any other function button is pressed.  
No show  
The message disappears after 4 seconds.  
PICTURE FREEZE FUNCTION  
Press the FREEZE button on the Remote Control Unit to freeze the picture on-screen. This function is cancelled when  
the FREEZE button is pressed again or any other function button is pressed.  
SOUND ADJUSTMENT  
It indicates the level of the volume.  
SOUND VOLUME ADJUSTMENT  
Press the VOLUME (+/) button(s) on the Top Control or on the  
Remote Control Unit to adjust the volume. The Volume dialog box  
appears on the screen for a few seconds.  
The VOLUME (+) button increases the volume, and The VOLUME  
() button decreases the volume.  
Press the MUTE button to set  
the Mute function On or Off.  
SOUND MUTE ADJUSTMENT  
The display disappears after 4 seconds.  
Press the MUTE button on the Remote Control Unit to cut off the  
sound. To restore the sound to its previous level, press again or  
press Volume button(s).  
22  
 
COMPUTER MODE  
SELECTING COMPUTER MODE  
COMPUTER / MCI  
DIRECT OPERATION  
button  
MODE button  
COMPUTER  
COMPUTER  
Select COMPUTER mode by pressing the MODE button on the Top  
Control or the COMPUTER / MCI button on the Remote Control Unit.  
MCI  
MCI  
VIDEO  
MENU OPERATION  
Press the MENU button and the ON-SCREEN MENU will appear.  
Press the POINT LEFT/RIGHT buttons to select Computer  
press the SELECT button.  
and  
CURRENT MODE DISPLAY  
When selecting the Computer Mode, the Current Mode display  
appears. It shows the information of the computer of the mode  
selected.  
Providing the information of the computer detected  
by the projector.  
SELECTING COMPUTER SYSTEM  
AUTOMATIC MULTISCANNING SYSTEM  
This projector automatically tunes to most different types of computer  
based on VGA, SVGA, XGA or SXGA (refer to COMPATIBLE  
COMPUTER SPECIFICATIONon page 26). When selecting  
Computer, this projector automatically tunes to the incoming signal  
and projects the proper image without any special setting. (Setting of  
the Computer System may be required when connecting some  
computers.)  
SYSTEM BOX  
It displays the SYSTEM  
being selected.  
Note : The projector may provides the messages below.  
The projector cannot discriminate or detect the  
input signal from the computer. Adjust and set the  
computer system manually. (Refer to page 24.)  
Go to PC adj.  
There is no signal input from the computer. Make  
sure the connection of the computer and the  
No signal  
projector is set correctly.  
TROUBLESHOOTING on page 44.)  
(Refer to  
The system being selected.  
SELECT COMPUTER SYSTEM MANUALLY  
To set the Computer system manually, select the mode on the ON-  
SCREEN MENU.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
SYSTEM and press the SELECT button. Another dialog box  
COMPUTER MODE Menu will appear.  
1
The systems on this  
dialog box can be  
selected.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the system that you want to set,  
2
and then press  
SELECT button.  
Closes the SYS-  
TEM Menu.  
23  
 
COMPUTER MODE  
PC ADJUSTMENT  
This Projector can automatically tune to the display signals from most personal computers currently distributed.  
However, some computers employ the special signal formats which are different from the standard ones and  
may not be tuned by Multiscanning of this projector. If this happens, the projector cannot reproduce a proper  
image and the image is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or  
a skewed picture.  
This projector has PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match  
with those exceptional signal formats and the projector has five independent memory areas to memorize those  
parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use  
it.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT RIGHT/LEFT buttons to select PC  
1
ADJUST  
and press the SELECT button. Another dialog  
box Where to reserveMenu will appear.  
In this dialog box, you can store the parameter into the area  
from Mode 1to Mode 5.When memorizing the new  
computer parameter, select the Mode with the message Free”  
by pressing the POINT UP/DOWN buttons and the SELECT  
button. To change the parameters of the Mode previously set,  
select the Mode with Stored.”  
2
3
This Mode has para-  
meters being stored.  
When the Mode is selected, Parameter adjustment dialog box  
appears. Move the arrow to the item that you want to change  
by pressing the POINT UP/DOWN buttons, and adjust each  
item to match with your computer. To change the value, press  
either the POINT RIGHT button or the POINT LEFT button.  
Refer to the next page for adjusting each item.  
The Vacant Mode.  
Manual set Computer  
Mode (1 to 5).  
Close the PC  
ADJUSTMENT Menu.  
Move the arrow to Storedand press the SELECT button. The  
parameter is memorized in the selected Mode.  
4
5
To activate the Mode manually adjusted in this PC  
ADJUSTMENT Menu, select the Mode at the SYSTEM  
SELECT Menu. (Refer to page 23.)  
Press the POINT  
RIGHT/LEFT  
button(s) to  
adjust the value.  
Press the  
SELECT button  
to set Full screen  
function on/off.  
24  
 
Total lines  
The number of the total vertical lines. Adjust the number to match  
the image of your personal computer.  
Total dots  
The number of the total dots in one horizontal period. Adjust the  
number to match the image of your personal computer.  
Horizontal / Vertical  
Adjustment of the horizontal or vertical |picture position. When the  
image is not centered on the screen, adjust each of those items.  
Clamp  
Press the  
SELECT button  
to select the  
typical resolution  
of the image.  
Adjustment of the clamp level. When the image has a dark bar(s),  
try this adjustment.  
Display area  
Adjustment of the area displayed with this projector. Select the  
resolution at the Display area dialog box, or adjust the number at  
the column of Hor Vto match the resolution of the image.  
Full Screen  
Set Onto resize the image with 4 x 3 aspect ratio to fit the  
screen.  
Each of the keys operates as follow.  
Reset  
Recalls the parameter data that was previously  
adjusted.  
Mode free  
Stored  
Quit  
Clears the parameter data previously set.  
Stores the parameters in the memory.  
Closes the PC ADJUST Menu.  
25  
 
COMPUTER MODE  
COMPATIBLE COMPUTER SPECIFICATIONS  
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and less than  
140 MHz of Dot Clock.  
ON-SCREEN  
DISPLAY  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
VGA 1  
VGA 2  
640 x 480  
720 x 400  
640 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
31.47  
31.47  
31.47  
37.86  
37.86  
37.50  
43.269  
34.97  
35.00  
15.734  
15.625  
35.156  
37.88  
46.875  
53.674  
48.08  
37.90  
34.50  
38.00  
38.60  
47.90  
32.70  
38.00  
49.72  
48.36  
68.677  
60.023  
56.47  
60.31  
48.50  
44.00  
63.48  
36.00  
59.88  
70.09  
70.09  
74.38  
72.81  
75.00  
85.00  
66.60  
66.67  
30  
XGA 10  
XGA 11  
XGA 12  
XGA 13  
XGA 14  
XGA15  
1024 x 768  
1024 x 768  
1024 x 768  
(Interlace)  
62.04  
61.00  
35.522  
46.90  
47.00  
58.03  
60.24  
68.68  
64.20  
62.50  
63.90  
63.34  
63.74  
71.69  
81.13  
63.98  
79.976  
60.00  
61.20  
71.40  
50.00  
50.00  
63.37  
76.97  
61.85  
46.43  
63.79  
75.00  
80.00  
45.00  
33.75  
33.75  
77.07  
75.70  
43.48  
58.20  
58.30  
72.0  
VGA 3  
VGA 4  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 864  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 960  
1152 x 900  
1152 x 900  
VGA 5  
VGA 6  
VGA 7  
MAC 19  
MAC21  
75.08  
75.06  
70.40  
58.60  
60.00  
59.98  
60.01  
67.19  
76.107  
60.02  
75.025  
60.00  
65.20  
75.60  
43.00  
47.00  
60.01  
72.00  
66.00  
43.35  
60.18  
75.08  
75.08  
60.00  
60.00  
60.00  
MAC LC13  
MAC 13  
RGB  
640 x 480  
SXGA 1  
SXGA 2  
SXGA 3  
SXGA 4  
SXGA 5  
SXGA 6  
SXGA 7  
SXGA 8  
SXGA 9  
SXGA 10  
SXGA 11  
SXGA 12  
SXGA 13  
SXGA 14  
––––––––  
––––––––  
RGB  
25  
SVGA 1  
SVGA 2  
SVGA 3  
SVGA 4  
SVGA 5  
SVGA 6  
SVGA 7  
SVGA 8  
SVGA 9  
SVGA 10  
SVGA 11  
SVGA 12  
MAC1 6  
XGA 1  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
56.25  
60.32  
75.00  
85.06  
72.19  
61.03  
55.38  
60.51  
60.31  
71.92  
51.09  
60.51  
74.55  
60.00  
84.997  
75.03  
70.07  
74.92  
60.02  
54.58  
79.35  
43.59  
1280 x 1024  
(Interlace)  
1280 x 1024  
(Interlace)  
SXGA 15 1280 x 1024  
SXGA 16 1280 x 1024  
SXGA 17  
SXGA 18  
1152 x 900  
1280 x 1024  
(Interlace)  
XGA 2  
XGA 3  
SXGA 19 1280 x 1024  
XGA 4  
MAC  
1280 x 960  
XGA 5  
MAC  
1280 x 1024  
––––––––  
XGA 6  
HDTV720p  
HDTV1035i  
HDTV1080i  
––––––––  
––––––––  
XGA 7  
XGA 8  
1024 x 768  
(Interlace)  
XGA 9  
NOTE : Specifications are subject to change without notice.  
26  
 
COMPUTER MODE  
PICTURE IMAGE ADJUSTMENT  
ADJUST PICTURE IMAGE MANUALLY  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
IMAGE and press the SELECT button. Another dialog box  
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the item that you want to change by  
pressing the POINT UP/DOWN buttons. To change the value,  
press either the POINT RIGHT button or the POINT LEFT  
button.  
Indicates the  
level of the item.  
Fine sync.  
Adjust the picture as necessary to eliminate flicker from the display.  
(From 0 to 255.)  
Move the arrow to  
the item and press  
POINT RIGHT /  
LEFT button.  
Total dots  
The number of the total dots in one horizontal period. Adjust the  
number to match your PC image.  
White balance (Red / Green / Blue)  
Move the arrow to the color that you want to adjust. Press POINT  
LEFT button to lighten the color, and press POINT RIGHT button to  
deepen the color. (From 0 to 63.)  
Close the PICTURE  
IMAGE ADJUSTMENT  
Menu.  
Contrast  
Press POINT LEFT button to decrease contrast, and press POINT  
RIGHT button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to adjust the image darker, and press  
POINT RIGHT button to adjust brighter. (From 0 to 63.)  
Each of the keys operates as follow.  
Reset  
Stored  
Quit  
Recalls the data previously adjusted.  
Stores the adjusted data in the memory.  
Closes the PICTURE IMAGE ADJUSTMENT Menu.  
NORMAL FUNCTION  
The normal picture level is preset on this projector at the factory and  
can be restored anytime you press the NORMAL button (located on  
the Top Control or on the Remote Control Unit). The Normal”  
display will be displayed on the screen for a few seconds.  
Normal  
27  
 
COMPUTER MODE  
AUTO IMAGE FUNCTION  
The Auto Image function is provided to automatically adjust Fine  
sync., Total dots, and Picture Position for most computers.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
1
AUTO IMAGE  
and press the SELECT button.  
Another dialog box AUTO IMAGE Menu will appear.  
Move the arrow to an item that you want to adjust by pressing  
the POINT UP/DOWN button. Change the setting On or Off by  
pressing the SELECT button.  
2
Fine sync.  
Adjust the picture as necessary to eliminate flicker from the display.  
This item can be adjusted manually. (Refer to page 27.)  
Total dots  
The number of the total dots in one horizontal period. This item can  
be adjusted manually. (Refer to page 27.)  
Starts the adjustment  
on the item set to "On".  
Position  
Move the arrow to  
the item and then  
press the SELECT  
button.  
Adjustment of the position of the image. This item can be adjusted  
manually. (Refer to page 28.)  
Close the PICTURE IMAGE  
ADJUSTMENT Menu.  
Move the arrow to Go!and press the SELECT button to start  
the Auto Image function.  
This adjustment can be executed by pressing AUTO IMAGE  
button on the Top Control and the Remote Control Unit.  
3
Stored  
Stores the On/Off setting of each item.  
Starts the Auto Image Adjustment.  
Go!  
Quit  
Closes the AUTO IMAGE ADJUSTMENT Menu.  
NOTE : The Fine sync., Total dots, and Picture Position of some  
computers may not be fully adjusted with the Auto Image  
Function. In that case, manual adjustment is required to  
make fine image. (Refer to page 27 to adjust "Fine sync." or  
"Total dots" and page 28 to adjust Picture Position.)  
PICTURE POSITION ADJUSTMENT  
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION  
ADJUSTMENT.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
1
POSITION  
and press the SELECT button. The PICTURE  
POSITION dialog box will appear.  
Move the image by pressing the POINT UP / DOWN / RIGHT /  
LEFT buttons.  
PICTURE POSITION  
dialog box  
2
Press the POINT UP  
/
DOWN / RIGHT / LEFT  
buttons to move the image  
To cancel POSITION mode, press the any buttons except SELECT,  
RIGHT CLICK, POINT, PAGE /or LASER button. To recall the  
position previously adjusted, press NORMAL button.  
28  
 
COMPUTER MODE  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
1
SCREEN  
and press the SELECT button. Another dialog  
box PICTURE SCREEN Menu will appear.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the function that you want to select  
and then press SELECT button.  
2
True  
To make the image its original size select True in the dialog box.  
When the original image size is larger than the screen size (1024 x  
768), this projector enters Digital Zoom mode automatically.  
Move the arrow to the  
function and press the  
SELECT button.  
Keystone  
When the image is distorted vertically, select Keystone in the dialog  
box. The ON-SCREEN menu and SCREEN ADJUST menu  
disappears and the message Keystoneis displayed. Correct the  
Keystone distortion by pressing the KEYSTONE /button or the  
POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT  
on page 21.  
Digital Zoom  
To adjust the image size or pan the image, select Digital zoom in  
the dialog box. The ON-SCREEN menu and SCREEN ADJUST  
menu disappears and the message D. Zoomis displayed.  
This projector also enters Digital Zoom mode by pressing the  
D.ZOOM /button on the Remote Control Unit.  
Refer to the following for operation.  
Expand function  
To expand the image size, press the D.ZOOM button or the SELECT button. The image is magnified by degrees.  
Compress function  
To compress the image size, press the D.ZOOM button or the RIGHT CLICK button. The image is reduced by  
degrees.  
Panning function  
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image  
is larger than the screen size.  
To cancel Digital Zoom mode, press any button except D.ZOOM /, SELECT, RIGHT CLICK, POINT, PAGE /or  
LASER button. To adjust the image to 1024 x 768, press NORMAL button.  
This projector cannot display any resolution higher than 1280 X 1024. If your computers screen resolution is higher  
than 1280 X 1024, reset the resolution lower before connecting the projector.  
The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode.  
The normal "Panning Operation" may not function properly if the computer system prepared with the "PC Adjust" is  
used.  
29  
 
VIDEO MODE  
SELECTING VIDEO MODE  
MODE button  
COMPUTER  
DIRECT OPERATION  
Select VIDEO mode by pressing the MODE button on the Top  
Control or the VIDEO button on the Remote Control Unit.  
MCI  
VIDEO  
MENU OPERATION  
Press the MENU button and the ON-SCREEN MENU will appear.  
Press the POINT LEFT/RIGHT buttons to select Video  
press the SELECT button.  
and  
SELECTING COLOR SYSTEM  
Press the MENU button and the ON-SCREEN MENU will  
This box indicates the  
system being selected.  
1
2
appear. Press the POINT LEFT/RIGHT buttons to select  
SYSTEM and press the SELECT button. Another dialog box  
VIDEO SYSTEM Menu will appear.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to "Auto", and then press the  
SELECT  
button.  
Auto  
The projector automatically detects the incoming Video system, and  
adjusts itself to optimize its performance.  
When the Video System is PAL-M or PAL-N, select the system  
manually.  
Move the arrow to  
the Mode and press  
the SELECT button.  
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N  
If the projector cannot reproduce the proper video image, it is  
required to select a specific broadcast signal format among PAL,  
SECAM, NTSC, NTSC 4.43, PAL-M, or PAL-N.  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the image in desirable size.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
1
SCREEN  
and press the SELECT button. Another dialog  
box PICTURE SCREEN ADJUSTMENT DISPLAY will appear.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the screen size that you want to  
2
set, and then press the  
SELECT button.  
Regular  
Normal Video Image size with 4 x 3 aspect ratio.  
Move the pointer to the function that and  
press the SELECT button.  
Wide  
Resizes the image for wide screen size with 16 x 9 aspect ratio.  
Keystone  
When the image is distorted vertically, select Keystone in the dialog  
box. Correct the Keystone distortion by pressing KEYSTONE /●  
button or POINT UP/DOWN button(s). Refer to KEYSTONE  
ADJUSTMENT on page 21.  
30  
 
VIDEO MODE  
PICTURE IMAGE ADJUSTMENT  
ADJUSTING THE PICTURE IMAGE  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
IMAGE and press the SELECT button. Another dialog box  
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the item that you want to adjust by  
pressing the POINT UP/DOWN buttons. To change the value,  
press either the POINT RIGHT button or the POINT LEFT  
button.  
Color  
Indicates the  
level of the item.  
Press POINT LEFT button to lighten the image, and press POINT  
RIGHT button to deepen the image. (From 0 to 63.)  
Move the arrow to  
the item and press  
POINT RIGHT /  
LEFT button.  
Tint  
Press POINT LEFT button to increase purple, and press POINT  
RIGHT button to increase green. (From 0 to 63.)  
White balance (Red / Green / Blue)  
Move the arrow to the color that you want to adjust. Press POINT  
LEFT button to lighten the color, and press POINT RIGHT button to  
deepen the color. (From 0 to 63.)  
Close the PICTURE  
IMAGE ADJUSTMENT  
Menu.  
Contrast  
Press POINT LEFT button to decrease contrast, and press POINT  
RIGHT button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to darken the image, and press POINT  
RIGHT button to brighten the image. (From 0 to 63.)  
Sharpness  
Press POINT LEFT button to soften the image, and press POINT  
RIGHT button to sharpen the image. (From 0 to 63.)  
Each of the keys operates as follow.  
Reset  
Stored  
Quit  
Recalls the data previously adjusted.  
Stores the data in the memory.  
Closes the PICTURE IMAGE ADJUSTMENT Menu.  
NORMAL FUNCTION  
The normal picture level is preset on this projector at the factory and  
can be restored anytime you press the NORMAL button (located on  
the Top Control or on the Remote Control Unit). The "Normal"  
display will be displayed on the screen for a few seconds.  
Normal  
31  
 
MCI MODE  
OPERATING THE PC CARD SLOT  
This projector has a PC CARD SLOT and the data in a memory card (SmartMedia with PC Card Adapter or PC  
card) can be displayed just by inserting the card into it. It is unnecessary to connect with other input equipment.  
Media Card Imager (supplied with CD-ROM) can edit the image data and record it into a memory card for  
projecting with the projector.  
PC with Windows 95  
Media Card Imager  
(CD-ROM)  
MC I  
PC Card  
(not supplied)  
Digital Camera  
SmartMedia with PC Card Adapter  
(supplied)  
PC CARD SLOT (Front)  
HOW TO LOAD THE MEMORY CARD INTO THE PROJECTOR  
LOAD  
PC CARD SLOT  
Insert PC Card Adapter (with SmartMedia) or PC card into PC CARD  
SLOT. Make sure EJECT button pops out.  
NOTE : Be sure to insert the memory card with the front side facing  
left of the projector. Do not insert the card in reverse. The  
card may be damaged.  
Memory Card  
Insert with the front side of the card  
to the left side of the projector.  
UNLOAD  
Press EJECT button, and the memory card pops out.  
NOTE : Do not take the card out of the PC CARD SLOT while the  
data is loading. Data and the card can be damaged.  
PC CARD INDICATOR  
WHEN THIS INDICATOR IS LIT, THE  
PROJECTOR IS READING OR WRITING THE  
DATA INTO THE MEMORY CARD. DO NOT  
REMOVE THE MEMORY CARD. DATA IN  
THE MEMORY CARD MAY BE DAMAGED.  
EJECT BUTTON  
32  
 
AVAILABLE DATA  
This projector can project the image data as follows through the PC  
CARD SLOT.  
The data edited by Media Card Imager.”  
The data of the resolution between VGA (640 X 480) and SXGA  
(1280 X 1024) in Bit Map type (BMP) or JPEG type (JPG), such as  
Digital Camera data, can be also displayed.  
(Some image data in XGA size may not be displayed properly. In  
that case, reset the resolution lower.)  
Media Card Imager  
Media Card Imager (CD-ROM) is supplied  
with this projector to edit the image data  
for projecting. Installation of Media Card  
Imager is recommended. Refer to  
Owners Manual of Media Card Imager for  
installation and operation.  
Refer to SHOW THE DATA IN THE MEMORY CARDon page 34  
to display the image data.  
AVAILABLE CARD  
SmartMedia (with PC Card Adapter) or a Type || PCMCIA-ATA Card can be used with this projector. (Those memory  
cards are supplied with this projector.)  
Refer to SMARTMEDIA AND PC CARD ADAPTER on pages 38 and 39 for operation.  
NOTE : Some PCMCIA Adapters or PC Cards are not available for this projector and cannot provide the image data. In  
that case, use our SmartMedia and PC Card Adapter.  
SELECTING MCI MODE  
When the memory card is inserted into PC CARD SLOT, MCI mode is automatically selected and the first  
Page of the latest Index is projected onto the screen. To switch to MCI mode manually, operate as follows.  
COMPUTER / MCI  
DIRECT OPERATION  
button  
MODE button  
COMPUTER  
Select MCI mode by pressing the MODE button on the Top Control  
or the COMPUTER / MCI button on the Remote Control Unit.  
COMPUTER  
MCI  
MCI  
VIDEO  
MENU OPERATION  
Press the MENU button and the ON-SCREEN MENU will appear.  
Press the POINT LEFT/RIGHT buttons to select MCI  
the SELECT button.  
and press  
33  
 
MCI MODE  
SHOW THE DATA IN THE MEMORY CARD  
BASIC OPERATION  
Insert the memory card and select MCI mode. The data on the  
memory card is displayed.  
1
2
Select the Index  
To change pages, press the PAGE or button. (When the  
Display Timeris set in the image with the Media Card Imager,  
the image is changed to another automatically.)  
To select Index or Page in the table, follow the instructions of  
INDEX SELECTION and PAGE SELECTION.  
Index  
Pages in the Index  
Index and Page  
The data edited with Media Card Imager is the Index format  
consisting of several Pages. To project the desirable image,  
select the Index and then select the Page in the Index.  
This projector can project only image data in Bit Map or JPEG format or the data edited by Media Card Imager  
(supplied) through the PC CARD SLOT. Other data is not compatible and should be edited and written to a memory  
card with Media Card Imager before loading PC CARD SLOT.  
(The data in Bit Map or JPEG format, such as the data captured with a digital camera, can be projected directly through  
PC CARD SLOT.)  
If there is data edited by Media Card Imager and other data (such as Bit Map or JPEG format) together on one memory  
card, the data edited by Media Card Imager has priority. The image data in Bit Map or JPEG format is not projected. In  
that case, edit that data and write it to the memory card with the Media Card Imager.  
INDEX SELECTION  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select VIEW  
and press the SELECT button. Another dialog box VIEW  
SETTING menu will appear.  
1
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to "Index", and then press the  
2
The table of Indexes in the memory card will  
SELECT button.  
appear.  
Press the POINT UP/DOWN/LEFT/RIGHT buttons to move to  
the Index that you want to project and press the SELECT  
button. The first Page of the Index selected is displayed.  
(Press SELECT button again to display the table of Pages.)  
Move the arrow to  
each operation and  
press the SELECT  
button.  
3
PAGE SELECTION  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select VIEW  
and press the SELECT button. Another dialog box VIEW  
SETTING menu will appear.  
1
2
3
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to "Page", and then press the  
The table of pages of the index card will  
SELECT button.  
appear.  
Press the POINT UP/DOWN/LEFT/RIGHT buttons to move to  
the Page that you want to project and press the SELECT  
button. The page selected is displayed on the screen.  
The table of Pages can be displayed by pressing the SELECT  
button when the page is displayed on full screen.  
34  
 
MCI MODE  
WRITE DATA INTO THE MEMORY CARD  
The data edited by Media Card Imager in the computer can be written to or read from the memory card with the  
PC Card drive of your Personal Computer or the PC CARD Slot of this projector.  
The data edited by Media Card Imager is written in Bit Map type (BMP) or JPEG type (JPG).  
ACCESS TO THE MEMORY CARD THROUGH THE PROJECTOR  
If your computer doesn't have the PC card writing equipment, the data can be written or read by connecting  
with this projector.  
NOTE : This operation can be made only by Media Card Imager in the Personal Computer.  
Connect the projector to the Personal Computer with the  
Control Cable for Serial Port (optionally supplied / refer  
to page 12, 13).  
Connect the projector to your computer with the Control Cable  
for Serial Port (optionally supplied). (Refer to CONNECTING  
COMPUTERon Page 12, 13.)  
1
Insert the memory card into PC CARD SLOT of the projector.  
And then, turn on the projector first then the computer.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select View  
and press the SELECT button. Another dialog box VIEW  
SETTING Menu will appear.  
2
Press POINT DOWN button and a red arrow will appear. Move  
the arrow to Card access by pressing POINT UP/DOWN  
button. And then press SELECT button. Ready to accessis  
displayed.  
Move the arrow to  
each operation and  
press the SELECT  
button.  
3
Operate Media Card Imager of your computer to write/read the  
in the PC card. (Refer to Owner's Manual of Media Card  
Imager for operation.)  
NOTE : Connect the projector to the computer with Control Cable  
before turning those appliances on.  
Do not press any button while read/write operations are in  
progress. Those operations will be canceled and the data in  
the memory card may be damaged.  
35  
 
MCI MODE  
PICTURE IMAGE ADJUSTMENT  
ADJUST THE PICTURE IMAGE MANUALLY  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
IMAGE and press the SELECT button. Another dialog box  
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the item by pressing the POINT  
UP/DOWN buttons. To change the value press either the  
POINT RIGHT button or the POINT LEFT button.  
Indicates the roughly  
level of the item.  
White balance (Red / Green / Blue)  
Move the arrow to the color that you want to adjust. Press POINT  
LEFT button to lighten the color, and press POINT RIGHT button to  
deepen the color. (From 0 to 63.)  
Move the arrow to  
the item and press  
POINT RIGHT /  
LEFT button.  
Contrast  
Press POINT LEFT button to decrease contrast, and press POINT  
RIGHT button to increase contrast. (From 0 to 63.)  
Close the PICTURE  
IMAGE ADJUSTMENT  
Menu.  
Brightness  
Press POINT LEFT button to darken the image, and press POINT  
RIGHT button to brighten the image. (From 0 to 63.)  
Each of the keys operates as follow.  
Reset  
Stored  
Quit  
Recalls the data previously adjusted.  
Stores the adjusted data in the memory.  
Closes the PICTURE IMAGE ADJUSTMENT Menu.  
NORMAL FUNCTION  
The normal picture level is preset on this projector at the factory and  
can be restored anytime you press the NORMAL button (located on  
the Top Control or on the Remote Control Unit). The "Normal"  
display will be displayed on the screen for a few seconds.  
Normal  
PICTURE POSITION ADJUSTMENT  
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION  
ADJUSTMENT.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
1
POSITION  
and press the SELECT button. The PICTURE  
POSITION dialog box will appear.  
PICTURE POSITION  
dialog box  
Move the image by pressing the POINT UP / DOWN / RIGHT /  
LEFT buttons.  
2
Press the POINT UP  
/
DOWN / RIGHT / LEFT  
buttons to move the image  
To cancel POSITION mode, press the any buttons except SELECT,  
RIGHT CLICK, POINT, AUTO IMAGE, PAGE /or LASER button.  
To recall the position previously adjusted, press NORMAL button.  
36  
 
MCI MODE  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the image desirable image  
seize.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
1
SCREEN  
and press the SELECT button. Another dialog  
box PICTURE SCREEN Menu will appear.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the function that you want to select  
and then press SELECT button.  
2
True  
To make image its original size select True in the dialog box. When  
the original image size is larger than the screen size (1024 x 768),  
this projector enters Digital Zoom mode automatically.  
Move the arrow to the  
function and press the  
SELECT button.  
Keystone  
When the image is distorted vertically, select Keystone in the dialog  
box. The ON-SCREEN menu and SCREEN ADJUST menu  
disappears and the message Keystoneis displayed. Correct the  
Keystone distortion by pressing KEYSTONE /button or POINT  
UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on  
page 21.  
Digital Zoom  
To adjust the image size or pan the image, select Digital zoom in  
the dialog box. The ON-SCREEN menu and SCREEN ADJUST  
menu disappears and the message D. Zoomis displayed.  
This projector also enters Digital Zoom mode by pressing D.ZOOM  
/button on the Remote Control Unit.  
Refer to the following for operation.  
Expand function  
To expand the image size, press D.ZOOM button or SELECT button. The image is magnified by degrees.  
Compress function  
To compress the image size, press D.ZOOM button or RIGHT CLICK button. The image is reduced by degrees.  
Panning function  
To pan the image, press POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is  
larger than the screen size.  
To cancel Digital Zoom mode, press any button except D.ZOOM /, SELECT, RIGHT CLICK, POINT, PAGE /,  
AUTO IMAGE, or LASER button. To adjust the image to 1024 x 768, press NORMAL button.  
This projector cannot display any resolution higher than 1280 X 1024. If your computers screen resolution is higher  
than 1280 X 1024, reset the resolution lower before connecting the projector.  
The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode.  
37  
 
MCI MODE  
SMARTMEDIA AND PC CARD ADAPTER  
SmartMedia and PC Card Adapter are provided with this LCD projector. SmartMedia can be used as a PC card  
conforming to the PC Card Standard-ATA by combining with PC Card Adapter.  
INSTALL / REMOVE THE SMARTMEDIA  
INSTALL  
PC Card Adapter  
(supplied)  
Insert SmartMedia fully into PC Card Adapter. Make sure EJECT  
button pops out.  
NOTE : The front side of SmartMedia has a Contact Area on its  
surface.  
SmartMedia  
(supplied)  
The front side of PC Card Adapter has the Eject button on  
the left side of the slot.  
Do not insert SmartMedia in reverse. The card and the data  
can be damaged.  
REMOVE  
To remove the SmartMedia, fully press in the EJECT button. The  
card pops out, then take out the card.  
NOTE : Do not pull SmartMedia by force. It may damage  
SmartMedia or PC Card Adapter.  
EJECT button  
IMPORTANT NOTE  
THE DATA STORED ON THE MEMORY CARD (SMARTMEDIA OR PC CARD) MAY BE DAMAGED OR  
LOST BECAUSE OF DAMAGE TO THE MEMORY CARD OR THE ACCIDENTAL ERASURE. IT IS REC-  
OMMENDED THAT ANY IMPORTANT DATA IS COPIED ONTO SEPARATE MEDIA, SUCH AS A FLOP-  
PY DISK, A HARD DISK, OR A MO DISK. WE SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS  
OF PROFITS ARISING FROM THE LOSS OF DATA BECAUSE OF ACCIDENTAL OPERATION AND  
DAMAGE TO A MEMORY CARD OR APPLIANCES. REFER TO OWNERS MANUAL OF MEDIA CARD  
IMAGER FOR OPERATING THE SOFTWARE.  
38  
 
MCI MODE  
PRECAUTIONS AND SPECIFICATIONS OF THE SMARTMEDIA  
SmartMedia is a precision device. Do not bend it, drop it, subject it  
to strong forces or shocks or place where a strong static electrical  
charge can be generated.  
Do not touch the surface of the Contact Area with fingers or allow it  
to be stained with foreign materials. Store SmartMedia inside its  
protective case when it is not used.  
SmartMedia is a consumable item. The data may not be written in  
or read from SmartMedia indefinitely. Occasionally replace  
SmartMedia with new one.  
Contact Area  
Memory capacity : 8MB  
Data is written in Contact Area. Never  
scratch or stain this area.  
Operating voltage : 3.3 V DC  
Usage environment  
Write Protect Area  
Temperature : 0~55 °C (during use)  
-20~65 °C (during storage)  
Humidity : less than 95% (during use, during storage)  
Affix Write Protect Sticker onto Write  
Protect Area to prevent from accidental  
erasure.  
CAUTION  
Index Area  
Write Protect Sticker is not available for PC. When PC attempts  
to read the data from SmartMedia with Write Protect Sticker, it pro-  
vides the error messages or the control of PC becomes insecure  
because of the property of the interface. When the error messages  
are displayed, press any key to return to the normal display. It is  
recommended, however, SmartMedia should be used on PC with-  
out Write Protect Sticker.  
Affix Index Label onto Index Area.  
PRECAUTIONS AND SPECIFICATIONS OF THE PC CARD ADAPTER  
Do not bend, drop, subject to strong forces or shocks or place  
where strong static electrical charge can be generated.  
Do not insert materials other than SmartMedia. The adapter may  
be damaged. Store PC Card Adapter inside its protective case  
when it is not used.  
Do not shake the adapter, turn off the appliances, or remove  
SmartMedia from the PC Card Adapter during writing or reading  
data. It may damage the data in SmartMedia.  
Operating voltage : 5 V DC  
Usage environment  
Temperature : 0~55 °C (during use)  
-20~65 °C (during storage)  
Humidity : less than 95%  
(during use, during storage)  
This adapter can be adapted to only our SmartMedia indicated below.  
Available SmartMedia : 3.3V / 5V, 2MB / 4MB / 8MB /16MB  
39  
 
SETTING  
SETTING MENU  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press the POINT LEFT/RIGHT buttons to select  
SETTING and press the SELECT button. Another  
dialog box SETTING Menu will appear.  
1
2
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the item that you want to set, and  
then press the  
SELECT button to set it "On" or "Off".  
When this function is in the "On" position, this projector  
will produce a blue image instead of the video noise on  
the screen when all the input source is unplugged or  
turned off.  
Blue back  
When this function is in the "On" position, the On-  
Screen Displays always appear when adjustments are  
made. (The following displays disappear by switching  
this function "Off.")  
Display  
Set the Pointer to the item,  
and then press the SELECT  
button.  
Preparation Display  
(The Number-counting-down Display)  
Mode Display  
Volume/Mute Display  
Zoom Display  
Focus Display  
Normal Display  
No show Display  
Keystone Display  
D.Zoom Display  
Ceiling function  
Rear function  
When this function is in the Onposition, the top /  
bottom and the left / right reversed picture is provided  
to project the image from a ceiling mounted projector.  
Ceiling  
Rear  
When this function is in the Onposition, the left / right  
reversed picture is provided to project the image to a  
rear projection screen.  
Turn this function Onposition in the SETTING menu.  
The picture will change into next one by sliding black  
image side ways like drawing the black curtains when  
the input source is turned into another one.  
Split wipe  
The Lamp age function is designed to reset the lamp  
replacement monitor timer. When replacing the lamp,  
reset the lamp replacement monitor timer by using this  
function. (Refer to page 43.)  
Lamp age  
SELECTING LANGUAGE  
The language used in the ON-SCREEN MENU is selectable from  
among English, German, French, Italian, Spanish and Japanese.  
Press the MENU button and the ON-SCREEN MENU will  
appear. Press POINT LEFT/RIGHT buttons to select  
LANGUAGE and press the SELECT button. Another dialog  
box LANGUAGE Menu will appear.  
1
Move the Pointer to the  
language that you want  
to set, and then press  
the SELECT button.  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move the arrow to the language that you want to set,  
2
and then press the  
SELECT button.  
40  
 
APPENDIX  
OPERATING WIRELESS MOUSE  
The Wireless Remote Control Unit is not only able to operate the projector but also can be used as a wireless  
mouse for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless  
mouse operation.  
The wireless mouse is available only when PC mouse pointer is displayed on the screen. When the menu or  
the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse  
cannot be used.  
INSTALLATION  
To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the  
mouse driver (not supplied) is required. Make sure that the mouse driver is properly installed in your  
computer. And make sure that the mouse port of the computer connected to Control Port is activated.  
Connect the mouse port of your computer to the Control Port of  
the projector with the Control Cable. (Refer to page 10 to 13 for  
connection.)  
1
Note : When the computer has no  
mouse port, connect the Serial  
Port of the computer to Control  
Port of the projector with the  
Control Cable for Serial Port.  
Turn the projector on first, and then turn on your computer.  
When the computer is switched on first, the Wireless Mouse  
may not work properly.  
2
OPERATING WIRELESS MOUSE  
When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT  
button, and RIGHT CLICK button on the Wireless Remote Control Unit.  
POINT button (Move the pointer)  
POINT button  
Used to move the pointer. The pointer is moved corresponding with  
the direction you are pressing.  
SELECT (LEFT CLICK) button  
This button has the same function as the left button in a PC mouse.  
RIGHT CLICK button  
This button has the same function as the right button in a PC mouse.  
Pressing this button does not affect any operation when in Menu  
mode.  
SELECT button  
(left button of the  
mouse)  
RIGHT CLICK button  
(right button of the mouse)  
41  
 
APPENDIX  
MAINTENANCE  
TEMPERATURE WARNING INDICATOR  
The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds  
the normal temperature. The Indicator stops flashing when the temperature of the projector become normal.  
When the TEMPERATURE WARNING Indicator continues to flash, check the item listed below.  
The Ventilation slots of the projector may be blocked. In such an event, reposition the appliance so that the  
ventilation slots are not obstructed.  
1
Air filters are clogged with dust particles. Clean the air filters by following AIR FILTER CARE AND CLEANING  
below.  
2
If the TEMPERATURE WARNING Indicator remains on after performing the above checks, the Cooling Fans or the  
Internal Circuits may be malfunctioning. In that case, call Boxlight.  
3
AIR FILTER CARE AND CLEANING  
The Removable Air Filters prevent dust from accumulating on the surface of the Projection Lens and the  
Projection Mirror. Should the Air Filters become clogged with dust particles, it will reduce the Cooling Fans'  
effectiveness and may result in internal heat build up and adversely affect the life of the projector.  
Clean the Air Filters following the steps below:  
Turn the power off, and disconnect the AC power cord from the  
AC outlet.  
AIR FILTERS  
1
Turn the projector upside down and remove 2 Air Filters by  
pulling the latches of them upward.  
2
Clean the Air Filters with brush or wash out the dust and  
particles.  
3
Replace the Air Filter. Make sure that the Air Filters are fully  
inserted.  
4
CAUTION  
Do not operate the projector with the Air Filter removed.  
Dust may become stuck on the LCD Panel and the Mirror,  
degrading the picture quality.  
Do not put the small parts into the Air Intake Vents. It  
result in malfunction of the projector.  
The Air Filter is small. Ensure that children dont eat or  
swallow it.  
RECOMMENDATION  
We recommend avoiding dusty/smoky environments for operating the projector. Using in these  
environment may cause poor image quality.  
When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel and lens inside it, and may  
resultantly be projected onto the screen together with the picture.  
When the above symptoms are noticed contact Boxlight at 1-800-762-5757 or 360-779-7901 for cleaning.  
CLEANING THE PROJECTION LENS  
Follow these steps to clean the projection lens:  
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.  
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.  
1
Lightly wipe the cleaning cloth over the lens.  
2
3
When you are not using the projector, replace the lens cover.  
42  
 
APPENDIX  
LAMP REPLACEMENT INDICATOR  
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights red.  
When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is  
required.  
LAMP REPLACEMENT  
CAUTION  
For continued safety, replace with a lamp assembly of the same type.  
Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector  
can become very hot.  
Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.  
Follow these steps to replace the lamp assembly.  
Turn off the projector and disconnect the AC plug. Allow the  
projector to cool for at least 45 minutes.  
1
Remove a screw with a screwdriver and remove the Lamp  
Cover.  
2
Remove 2 screws with a screwdriver and pull out the Lamp  
Assembly by grasping the handle.  
3
LAMP COVER  
Replace the Lamp Assembly with new one and tighten 2  
screws. Make sure that the Lamp Assembly is set properly.  
And replace the Lamp Cover and tighten a screw.  
4
HANDLE  
Connect the AC Power Cord to the projector and turn the  
projector on.  
5
6
Reset the Lamp Replacement Monitor Timer (refer to the  
section Lamp Replacement Monitor Timerbelow).  
NOTE : Do not reset the LAMP REPLACEMENT MONITOR  
LAMP  
ASSEMBLY  
TIMER, when the lamp is not replaced.  
ORDER REPLACEMENT LAMP  
Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901.  
Model No. of your projector : BOXLIGHT CP-33t  
Replacement Lamp Type No. : POA-LMP21J  
(Service Parts No. 610 280 6939)  
LAMP REPLACEMENT MONITOR TIMER  
Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the  
Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.  
Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT  
1
LEFT/RIGHT buttons to select SETTING  
box SETTING MENU will appear.  
and press the SELECT button (refer to page 40). Another dialog  
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the  
SELECT button. The message "Lamp replace monitor Reset?" is displayed.  
2
3
Select [Yes] to reset the Timer.  
Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.  
43  
 
APPENDIX  
TROUBLESHOOTING  
Before calling BOXLIGHT or your dealer or service station for assistance, check the matters below once again.  
1. Make sure you have connected the projector to your equipment a s described in the section "CONNECTING  
THE PROJECTOR" on pages 10 ~ 13.  
2. Check cable connection. Verify that all computer, video and power cord are properly connected.  
3. Verify that all power is switched on.  
4. If the projector still does not produce the image, re-start the computer.  
5. If the image sill does not appear, unplug the projector from the computer and check the computer monitor's  
display. The problem may be with your graphics controller rather than with the projector. (When you  
reconnect the projector, remember to turn the computer and monitor off before your power up the projector.  
Power the equipment back in order of : Projector and computer.)  
6. If the problem still exists, check with the following chart.  
Problem:  
No power.  
Try these Solution  
Plug the projector into the AC outlet.  
Be sure READY Indicator light is On.  
Wait 90 seconds after the projector is turned OFF before turning the projector back on.  
NOTE : After pressing the power ON-OFF switch to OFF, make sure the projector works  
as follow.  
1. The LAMP indicator will light and the READY indicator will turn off.  
2. After 90 seconds, the READY indicator will light green again and the projector  
may be turned on by pressing the power ON-OFF button.  
Check the TEMPERATURE WARNING indicator. If the indicator flashes red, the  
projector cannot be turned on.  
(See "TURNING ON/OFF THE PROJECTOR" section on page 20.)  
Check the Projection Lamp. (Refer to page 43.)  
Adjust the focus  
Image is out of  
focus.  
Make sure the projection screen is at least 4.6(1.4m) from the projector.  
Check the projection lens to see if it needs cleaning.  
NOTE : Moving the projector from a cool temperature location to a warm temperature  
location may result in moisture condensation on the lens. In such an event, leave  
the projector OFF an d wait until condensation disappears.  
Check Ceiling / Rear feature. (See SETTINGsection on page 40.)  
Check Ceiling feature. (See SETTINGsection on page 40.)  
Picture is Left/Right  
reversed.  
Picture is  
Top/Bottom  
reversed.  
Check Display feature.(See SETTINGsection on page 40.)  
Some displays are  
not seen during the  
Operation.  
Check the connection between the computer or video equipment and the projector.  
When turning the projector on, it takes about 30 seconds to display the image.  
Check the system that you select is corresponding with the computer or the video  
equipment.  
No image.  
Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).  
Check audio cable connection from audio input source.  
Adjust the audio source.  
No sound.  
Press VOLUME (+) button.  
Press MUTE button.  
44  
 
APPENDIX  
Problem:  
Remote Control Unit  
does not work.  
Try these Solution  
Check the batteries.  
Check the ALL-OFF switch on the Remote Control Unit is set to ON..  
Make sure nothing is between the Remote Receiver and the Remote Control Unit.  
Make sure you are not too far from the projector when using the Remote Control Unit.  
Maximum operating range is 16.4(5m).  
Check the cable connection between the projector and the computer.  
Check the mouse setting on your computer.  
Turn the projector on before you turn on the computer.  
Wireless Mouse  
function does not  
work.  
Check the memory card is inserted properly into PC CARD SLOT.  
Check SmartMedia or PC Card Adapter is set properly.  
Check MCI mode is selected.  
Check the image data is recorded in the memory card properly.  
Start the projector again.  
The image data in  
memory card isnt  
displayed.  
Check the projector is turned on.  
Check Card accessin VIEW menu is selected.  
Check Control Cable for Serial Port (optional) is connected properly.  
Check the memory card is inserted properly into PC CARD SLOT.  
Check Media Card Imager (supplied) is installed in your computer properly.  
Check the setting in Media Card Imager (like Serial Port Setting) is set properly.  
The image data cant  
be written in, read  
from the memory  
card.  
WARNING :  
High voltages are used to operate this projector. Do not attempt to open the cabinet.  
Boxlight Service is easily obtained. If after following instructions above, you find that service is necessary,  
contact Boxlight for assistance at 1-800-762-5757 or 360-779-7901.  
Give the model number and explain the difficulty. We will advise you how to obtain service.  
Please have the following information available.  
Serial No. of projector.  
Resolution of the computer.  
Refresh rate of computer.  
45  
 
TECHNICAL SPECIFICATIONS  
Multi-media Projector  
Projector Type  
(not including Adjustable Feet)  
9.41" x 3.54" x 12.72" (239mm x 90mm x 323mm)  
8.82 lbs (4.0 kg)  
(W x H x D)  
Dimensions  
Net Weight  
0.9" TFT Active Matrix type, 3 panels  
1024 x 768 dots  
LCD Panel System  
Panel Resolution  
Number of Pixels  
Color System  
2,359,296 (1024 x 768 x 3 panels)  
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N  
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz  
Adjustable from 30to 300”  
Scanning Frequency  
Projection Image size  
Horizontal Resolution  
Projection Lens  
Throw Distance  
(Diagonal)  
800 TV lines  
F 1.7 ~ 2.0 lens with f 33.2mm ~ 43.1mm Motor zoom and focus  
4.6~ 35.4(1.4 m ~ 10.8 m)  
150 W  
Projection Lamp  
AV Input Jacks  
RCA Type x 1 (Video, Audio R and L) and Mini DIN 4 pin (S-Video) x 1  
(VGA) HDB 15 Terminal x 1  
Computer Input Jacks  
Control Port Jack  
Monitor Output Jack  
Mini DIN 8 pin x 1  
(VGA) HDB 15 Terminal x 1  
Mini Jack (stereo)  
Computer Audio Input Jack  
Audio Output Jack  
Internal Audio Amp  
Built-in Speaker  
Mini Jack (stereo)  
1W RMS (Monaural)  
1 speaker, 1.57" x 1.18" (40mm x 30mm)  
0˚ to 10˚  
Feet Adjustment  
AC 100 ~ 120 V or 200 - 240 V, 50 / 60 Hz  
2.5 A / 1.4 A (Max. Ampere)  
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)  
Voltage  
Power Consumption  
Operating Temperature  
Storage Temperature  
Remote Control Transmitter  
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)  
Power Source  
Operating Range  
Dimensions  
Net Weight  
Laser Pointer  
:
:
:
:
:
AA,UM3 or R06 Type x 2  
16.4(5m) / ±30˚  
2.2x 1.3x 7.6(55mm x 34mm x 192mm)  
0.35 lbs (160 g) (including batteries)  
(Max. Output : 1mW / Wave length : 650±20nm)  
Class II Laser  
Owners Manual  
Accessories  
AC Power Cord  
Remote Control Transmitter and Batteries  
VGA Cable  
Control Cable for PS/2 port  
Media Card Imager for Windows 95 (CD-ROM)  
and Owner's Manual for this software  
SmartMedia and PC Card Adapter  
Dust Cover  
Lens Cover  
The specifications are subject to change without notice.  
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It  
is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty  
and electrical hazards.  
46  
 
OPTIONAL PARTS  
The parts listed below are optionally supplied. When ordering those parts, give the  
name and the Type No. of it to the sales dealer.  
Control Cable for Serial Port  
Control Cable for ADB Port  
MAC Adapter  
Type No. : POA-MCSRL  
Type No. : POA-MCMAC  
Type No. : POA-MACAP  
47  
 
LIMITED WARRANTY  
BOXLIGHT CORPORATION (BOXLIGHT) warrants that each Boxlight CP-33t (the Product) sold hereunder will  
conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply  
only to the first person or entity that purchases the Product for personal or business use and not for the purpose of  
distribution resale. Said warranty shall continue for a period of two (2) years from the date of such purchase.  
BOXLIGHT does not warrant that the Product will meet the specific requirements of the first person or entity that  
purchases the Product for personal or business use. Lamp is warrantied for 120 days.  
BOXLIGHT CORPORATIONs liability for the breach of the foregoing limited warranty is limited to the repair or  
replacement of the Product or refund of the purchase price of the Product, at BOXLIGHTs sole option. To exercise  
the Purchasers rights under the foregoing warranty, the Product must be returned at the Purchasers sole cost and  
expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by  
a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealers name; (iii) the model  
and serial number of the Product. A return authorization number, issued by the BOXLIGHT customer service  
department, must also be clearly displayed on the outside of the shipping carton containing the Product.  
WARRANTY LIMITATION AND EXCLUSION  
BOXLIGHT CORPORATION shall have not further obligation under the foregoing limited warranty if the Product has  
been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized  
modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than  
from ordinary use or failure to properly use the Product in the application for which said Product is intended.  
DISCLAIMER OR UNSTATED WARRANTIES  
The warranty printed above is the only warranty applicable to this purchase.  
All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and  
fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof and the  
foregoing warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT  
CORPORATION.  
LIMITATION OR LIABILITY  
It is understood and agreed that BOXLIGHTs liability whether in contract, in tort, under any warranty, in negligence or  
otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no  
circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the  
Product is a consideration in limiting BOXLIGHTs liability. No action regardless of form, arising out of the agreement  
to purchase the product, may be brought by purchaser more than one year after the cause of action has accrued.  
BOXLIGHT  
®
Boxlight  
19332 Powder Hill Place  
Poulsbo, WA 98370-7407 USA  
U.S. and Canada 800-762-5757  
International 360-779-7901  
Printed in Japan  
Part No. 610 283 5137 (1AA6P1P2220-- MB6L)  
 

BenQ Projector MW767 User Manual
Black Decker Chainsaw CS1015 User Manual
Breville Mixer ABN77000085549 User Manual
Broan Patio Furniture Premier User Manual
Bushnell Telescope 786050 User Manual
Canon Fax Machine D680 User Manual
CDA Refrigerator FW950 User Manual
Chief Manufacturing Indoor Furnishings RPA U User Manual
Chromalox Thermostat PK477 User Manual
Cisco Systems IP Phone OL 21035 01 User Manual